灌注混凝土桩施工方法及工艺的探讨

通过对钻孔灌注桩与沉入桩的对比分析,得出了钻孔灌注桩的优点,并且详细介绍了钻孔灌注桩的施工工艺和方法,总结了提高灌注混凝土桩承载力的方法和灌注桩的检测手段及一般事故处理方法,以供今后类似工程实践参考.     

复杂地质和环境条件下水闸围堰工程设计技术

在河流中建设水闸、船闸,其围堰工程是保证主体工程安全干施工的重要前提和保障。结合某水闸工程设计,针对围堰设计遇到的地质和环境条件复杂、施工场地狭窄、施工期不断流等难题,开展围堰总体布置、纵横向围堰结构设计、支护围堰结构设计、围堰止水墙设计等一系列关键技术问题研究。采用研究成果设计的方案不仅可以减少围堰工程量、节约工期,而且能确保项目顺利安全实施。     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

基于ANN的船舶撞击高桩码头群桩损伤位置预测

本文采用有限元软件ABAQUS建立了船舶撞击高桩码头群桩的空间有限元模型。通过计算评估了撞击力、桩体刚度、撞击位置和撞击角度下对群桩结构损伤位置的影响。基于人工神经网络(ANN)方法,对不同参数组合下的群桩结构损伤位置进行了预测,并对ANN方法的可行性进行了评估。     

基于Prover的联锁软件形式化验证过程研究

计算机联锁系统是铁路信号控制系统的核心设备,是有着苛刻安全要求的复杂控制系统。本文采用Prover形式化开发工具对联锁软件安全需求进行形式化验证。通过模型检验的形式化验证方法,遍历系统输入变量的所有状态空间.验证联锁特定应用满足系统安全需求,确保系统的安全性得以正确实现。在保证系统安全性的基础上,以全状态空间查找反例的检验方法进一步提升产品的质量。     

桥墩及桩基形式对墩底平转施工转盘设计的影响

以新建福厦(福州—厦门)高速铁路17500 t转体刚构为背景,采用实体有限元方法分析了不同桥墩类型及桩基布置对墩底平转转体中转盘受力的影响,并对桥墩及桩基进行了优化。结果表明:实体墩对上转盘受力最有利,其次是空心墩,最不利的是双薄壁墩;增加墩底实体段能够有效降低空心墩、双薄壁墩上转盘的主拉应力;随着墩底实体段高度的增加,主拉应力降低的幅度逐渐变小;球铰正下方有桩基时对下转盘底部受力更加有利;距离球铰中心越远,桩基受力越小,适当增加中桩桩径,可使各桩基应力状态更加均衡。     

Estimating traffic volumes for signalized intersections using connected vehicle data

Recently connected vehicle (CV) technology has received significant attention thanks to active pilot deployments supported by the US Department of Transportation (USDOT). At signalized intersections, CVs may serve as mobile sensors, providing opportunities of reducing dependencies on conventional vehicle detectors for signal operation. However, most of the existing studies mainly focus on scenarios that penetration rates of CVs reach certain level, e.g., 25%, which may not be feasible in the near future. How to utilize data from a small number of CVs to improve traffic signal operation remains an open question. In this work, we develop an approach to estimate traffic volume, a key input to many signal optimization algorithms, using GPS trajectory data from CV or navigation devices under low market penetration rates. To estimate traffic volumes, we model vehicle arrivals at signalized intersections as a time-dependent Poisson process, which can account for signal coordination. The estimation problem is formulated as a maximum likelihood problem given multiple observed trajectories from CVs approaching to the intersection. An expectation maximization (EM) procedure is derived to solve the estimation problem. Two case studies were conducted to validate our estimation algorithm. One uses the CV data from the Safety Pilot Model Deployment (SPMD) project, in which around 2800 CVs were deployed in the City of Ann Arbor, MI. The other uses vehicle trajectory data from users of a commercial navigation service in China. Mean absolute percentage error (MAPE) of the estimation is found to be 9–12%, based on benchmark data manually collected and data from loop detectors. Considering the existing scale of CV deployments, the proposed approach could be of significant help to traffic management agencies for evaluating and operating traffic signals, paving the way of using CVs for detector-free signal operation in the future.     

Theory of safety surrogates using vehicle trajectories in macroscopic and microscopic settings: Application to dynamic message signs controlled traffic at work zones

This paper presents a new mathematical framework for obtaining quantitative safety measure using macroscopic as well as microscopic traffic data. The safety surrogate obtained from the macroscopic data is in terms of analysis performed on vehicle trajectories obtained from the macroscopic data. This method of obtaining safety measure can be used for many different types of applications. The safety surrogate for the traffic dynamics are developed in terms of a new concept of Negative Speed Differentials (NSD) that involve a convolution of vehicle speed function obtained from vehicle trajectories and then performing the integration of the square of the output for its negative values. The framework is applicable to microscopic traffic dynamics as well where we can use car following models for microscopic dynamics or the LWR model for macroscopic dynamics. This paper then presents the use of this new safety surrogate on the development of a feedback control law for controlling traffic in work zones using Dynamic Message Signs. A hybrid dynamics model is used to represent the switching dynamics due to changing DMS messages. A feedback control design for choosing those messages is presented as well as a simple simulation example to show its application.     

Multi-criteria optimization of traffic signals: Mobility,safety, and environment

Two-dimensional multi-objective optimizations have been used for decades for the problems in traffic engineering although only few times so far in the optimization of signal timings. While the other engineering and science disciplines have utilized visualization of 3-dimensional Pareto fronts in the optimization studies, we have not seen many of those concepts applied to traffic signal optimization problems. To bridge the gap in the existing knowledge this study presents a methodology where 3-dimensional Pareto Fronts of signal timings, which are expressed through mobility, (surrogate) safety, and environmental factors, are optimized by use of an evolutionary algorithm. The study uses a segment of 5 signalized intersections in West Valley City, Utah, to test signal timings which provide a balance between mobility, safety and environment. In addition, a set of previous developed signal timing scenarios, including some of the Connected Vehicle technologies such as GLOSA, were conducted to evaluate the quality of the 3-dimensional Pareto front solutions. The results show success of 3-dimensinal Pareto fronts moving towards optimality. The resulting signal timing plans do not show large differences between themselves but all improve on the signal timings from the field, significantly. The commonly used optimization of standard single-objective functions shows robust solutions. The new set of Connected Vehicle technologies also shows promising benefits, especially in the area of reducing inter-vehicular friction. The resulting timing plans from two optimization sets (constrained and unconstrained) show that environmental and safe signal timings coincide but somewhat contradict mobility. Further research is needed to apply similar concepts on a variety of networks and traffic conditions before generalizing findings.     

基于模糊层次的铁路混装货物装运安全评价研究

随着客户运输需求的多样化升级,采用铁路混装货物装运模式在提升铁路运输效率、吸引多样货源等方面相较于单一品名装运显示出一定的优越性,同时混装货物装运面临的安全压力相较于单一品名装运出现骤增。为保障铁路混装货物装运安全,在阐述混装货物装运特点及安全控制要点的基础上,从"人防""物防""技防"3方面构建混装货物装运安全评价指标体系,采用层次分析法确定各指标权重,并利用模糊综合评价法对铁路混装货物装运安全进行评价,通过实例验证该评价方法的实用性及有效性,为铁路混装货物装运安全评价提供依据。