典型钢桥面铺装结构的病害分类分析

本文结合国内外钢桥面铺装损坏的实际情况,分析总结了四种典型钢桥面铺装结构产生的病害情况,并在此基础上对钢桥面铺装的病害进行了分类。     

可变截面涡轮增压瞬态性能仿真研究

为研究可变截面涡轮喷嘴开度对发动机的性能影响,建立GT-power和MATLB/Simulink联合仿真模型。采用GT-power软件建立的TBD234V12可变截面涡轮增压柴油机仿真模型研究发动机稳态性能,联合MATLB/Simulink软件建立的可变截面涡轮增压柴油机控制模型,对发动机瞬态性能进行仿真计算。结果表明:在发动机瞬态工况下,可变截面涡轮增压系统可以明显改善常规增压柴油机的动力性、经济性和动态响应特性,并且有效降低增压柴油机的时滞性,涡轮迟滞时间的降幅约为30%。     

船舶制造企业辅助生产核算体系

船舶制造企业辅助生产核算由于劳务种类多、金额大、交互频繁、计量方式各不相同,成为造船成本核算中的难点,也直接影响船舶产品成本的准确性。本文在对各种分配方法进行分析研究的基础上,结合造船企业产品特点和辅助生产部门提供的劳务特点,提出对劳务进行分类,根据分类分别制定相应的辅助生产分配方法的观点,并用案例验证方法的可行性和适用性。文章的研究结果为船舶制造企业辅助生产核算和成本控制提供参考。     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

地铁暗挖隧道二次衬砌施工质量控制浅析

文章根据深圳轨道交通二期工程安托山站—侨香站暗挖区间的二次衬砌施工经验,分析了地铁暗挖隧道二次衬砌施工质量的影响因素以及二次衬砌施工过程中容易发生的质量问题,并提出了具体的控制措施。通过经验总结,使地铁施工的管理、质量控制、施工通病防治上升一个台阶。     

粉喷桩施工技术在高速公路软基加固中的应用

文章结合某高速公路软基加固工程实例,介绍了粉喷桩软基加固处理施工的工艺流程及技术要点,并分析了影响粉喷桩软基加固施工的主要因素,提出了相应的质量控制措施。     

浅埋偏压段隧道洞口地表沉降变形控制分析

文章对岜肯隧道浅埋偏压段洞口施工中出现的塌方及初衬开裂情况进行客观分析,结合施工实际提出了地表加固及平衡土体偏压措施,有效地控制了地表变形及隧道沉降开裂,保证了隧道施工安全、顺利进行。     

Ecologically based hybrid life cycle analysis of continuously reinforced concrete and hot-mix asphalt pavements

An ecologically-based hybrid life cycle assessment model is used to evaluate the resource consumption and atmospheric emissions of continuously reinforced concrete and a hot-mix asphalt pavements. The cumulative mass and ecological resource consumption values are lower for continuously reinforced concrete, but the median values of cumulative energy and industrial energy consumption were lower for hot-mix asphalt. In addition, the use of reclaimed asphalt pavement results in a higher sensitivity for the ecological resource consumption of hot-mix asphalt compared to that of fly ash when use on the natural capital utilization of continuously reinforced concrete pavement. The cumulative and industrial exergy consumption values are significantly reduced with increases in reclaimed asphalt pavement and fly ash, and the use of low fuel transportation modes.     

旧水泥混凝土路面冲击碾压技术初探

文章结合G206国道宿州至怀远段旧水泥混凝土路面改造施工实例,介绍了冲击碾压施工的原理、特点、质量控制措施及安全文明施工注意事项,并分析了冲击碾压施工中存在的问题与对策,为类似工程的改造施工提供参考。     

高速公路“三背”回填施工及质量控制探讨

文章介绍了高速公路桥台背、涵背、挡土墙墙背（简称＂三背＂）的回填施工工艺,阐述了＂三背＂回填的施工、检测要求及质量控制措施。