级配碎石混合料的动力变形特性

采用在古典 C.B.R法的基础上 ,施加动荷载的简化试验方法 ,分析级配碎石混合料的动力变形特性 ,可用永久变形、弹性模量双指标指导混合料的组成设计 ,而合理的级配碎石基层材料组成 ,应考虑到材料与振动碾压工艺的相互作用。     

低强度桩复合地基处理桥头跳车现场试验研究

介绍了浙江台州浃里陈大桥成功地采用低强度混凝土桩复合地基处理桥头跳车问题，同时通过现场载荷试验、桩顶和桩间土的土压力测试以及沉降观测，较全面地研究了低强度桩复合地基承载力和桩土受力特性以及沉降变化规律，得到了一些可供理论研究和工程实践借鉴的有益结论。     

粉喷桩加固软土复合路基受力特性试验研究

对杭州绕城高速公路(北线)进行了路堤荷载下粉喷桩加固软基现场试验研究，以期对软土复合路基的桩土应力比及桩身应力加深认识。     

钢管拱吊装阶段中温度的影响分析

就缆索吊装钢管拱的施工方法，以工程实例讨论钢管拱在吊装阶段中温度对安装精度和应力测试结果的影响。     

环氧沥青在大跨径钢桥面粘结层中的应用研究

粘结层材料和施工技术是大跨径钢桥面铺装的关键技术之一。根据某公路大桥桥面铺装粘结层的设计过程和特性，提出了环氧沥青粘结层的设计方法。     

连云港海相软土基本特性与处理方法探讨

根据连云港地区多条高速公路工程的地质资料,并与我国部分沿海地区软土进行对比,分析连云港海相软土的基本物理力学指标统计特征、抗剪强度特性、固结变形特性以及蠕变特性,并介绍了适合于该海相软土的主要地基处理措施。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.