Point-to-point speed enforcement systems: Speed limits design criteria and analysis of drivers’ compliance

Point-to-point (P2P) speed enforcement is a relatively new approach to traffic law enforcement. Its technology allows vehicles whose average speed exceeds the speed limit over the controlled section to be fined. It therefore encourages compliance over distances longer than those where spot enforcement policies have been in place.In this paper, a procedure for consistently setting speed limits with such enforcement systems is proposed. Such a method has been applied to design the speed limits on two motorways in the district of Naples, Italy, where P2P enforcement systems became operational in 2009 and 2010. The speed limits, which were set using the Italian geometric design standard to assess vehicle stability and stopping sight distance, have been compared with those provided by using well-known international standards.The impact of the newly designed speed limits and of the P2P enforcement system on drivers’ speeding behaviour has been quantified for each highway section and vehicle type. In fact, accurate measurements of the average travel speeds of each vehicle crossing the enforced sections, before and after the activation of the system, were available. The migration from the old speed limits with spot speed enforcement to the new approach resulted in a notable increase in drivers’ compliance to the speed limits with a remarkable decrease in both the average of individual speeds and in their standard deviation.In addition, the analysis of 3 years of data shows that a gradual adaptation of drivers’ behaviour to the system took place. In particular, a decreasing compliance to the speed limits points to a non-optimal system management. Finally, the results of a revealed preference survey allowed us to make a behavioural interpretation regarding the significantly different impacts measured on the two motorways.     

On the fundamental diagram for freeway traffic: A novel calibration approach for single-regime models

The speed-density or flow-density relationship has been considered as the foundation of traffic flow theory. Existing single-regime models calibrated by the least square method (LSM) could not fit the empirical data consistently well both in light-traffic/free-flow conditions and congested/jam conditions. In this paper, first, we point out that the inaccuracy of single-regime models is not caused solely by their functional forms, but also by the sample selection bias. Second, we apply a weighted least square method (WLSM) that addresses the sample selection bias problem. The calibration results for six well-known single-regime models using the WLSM fit the empirical data reasonably well both in light-traffic/free-flow conditions and congested/jam conditions. Third, we conduct a theoretical investigation that reveals the deficiency associated with the LSM is because the expected value of speed (or a function of it) is nonlinear with regard to the density (or a function of it).     

Towards data-driven car-following models

Car following models have been studied with many diverse approaches for decades. Nowadays, technological advances have significantly improved our traffic data collection capabilities. Conventional car following models rely on mathematical formulas and are derived from traffic flow theory; a property that often makes them more restrictive. On the other hand, data-driven approaches are more flexible and allow the incorporation of additional information to the model; however, they may not provide as much insight into traffic flow theory as the traditional models. In this research, an innovative methodological framework based on a data-driven approach is proposed for the estimation of car-following models, suitable for incorporation into microscopic traffic simulation models. An existing technique, i.e. locally weighted regression (loess), is defined through an optimization problem and is employed in a novel way. The proposed methodology is demonstrated using data collected from a sequence of instrumented vehicles in Naples, Italy. Gipps’ model, one of the most extensively used car-following models, is calibrated against the same data and used as a reference benchmark. Optimization issues are raised in both cases. The obtained results suggest that data-driven car-following models could be a promising research direction.     

激励措施在团队管理中的应用

文章以南宁高速公路运营有限公司团队管理为例,介绍了高速公路运营管理团队的构成特点及存在的问题,提出了基于考评激励、人才培养激励、目标激励、竞赛激励、尊重与关怀激励的团队管理措施,并阐述了激励措施在团队建设中的实践效果。     

盾构法施工单机核算管理模式的应用

近年来盾构机越来越多地应用于各种隧道工程中,其中地铁应用的数量最多,约占80%。现代盾构已演变成为一种高度智能化的大型工程机械装备,对其控制的好坏将直接影响到整个工程的施工成本和企业的经营效益,而通过单机核算降低机械成本是降低施工成本、提高企业效益的有效手段,因此推行盾构法施工单机核算显得尤为重要。文章结合地铁2222标施工项目,重点介绍了盾构法单机核算管理模式及其在施工中的应用。     

Speed variation during peak and off-peak hours on urban arterials in Shanghai

Increased speed variation on urban arterials is associated with reductions in both operational performance and safety. Traffic flow, mean speed, traffic control parameters and geometric design features are known to affect speed variation. An exploratory study of the relationships among these variables could provide a foundation for improving the operational and safety performance of urban arterials, however, such a study has been hampered by problems in measuring speeds. The measurement of speed has traditionally been accomplished using spot speed collection methods such as radar, laser and loop detectors. These methods can cover only limited locations, and consequently are not able to capture speed distributions along an entire network, or even throughout any single road segment. In Shanghai, it is possible to acquire the speed distribution of any roadway segment, over any period of interest, by capturing data from Shanghai’s 50,000+ taxis equipped with Global Positional Systems (GPS). These data, hereafter called Floating Car Data, were used to calculate mean speed and speed variation on 234 road segments from eight urban arterials in downtown Shanghai. Hierarchical models with random variables were developed to account for spatial correlations among segments within each arterial and heterogeneities among arterials. Considering that traffic demand changes throughout the day, AM peak, Noon off-peak, and PM peak hours were studied separately. Results showed that increases in number of lanes and number of access points, the presence of bus stops and increases in mean speed were all associated with increased speed variation, and that increases in traffic volume and traffic signal green times were associated with reduced speed variation. These findings can be used by engineers to minimize speed differences during the road network planning stage and continuing through the traffic management phase.     

The pros and cons of Intelligent Speed Adaptation as a restrictive measure for serious speed offenders

In 2011 in the Netherlands a field operational test was performed to investigate the possibility of using restrictive Intelligent Speed Adaptation (ISA) as a penalty system for serious speed offenders. This paper presents the overall results of the research focusing on the pros and cons of the use of ISA as a restrictive measure for serious speed offenders, and on the preconditions for deployment. The results showed that the ISA systems tested have a huge effect on driver behavior and have the potential to improve road safety by reducing the level of speeding, mean speed, as well as the standard deviation of speed. However, there are also cons: the behavioral change in driving behavior was only temporary. In addition the tested technology proved too easy to override, raised issues of equity, and a substantial back office is required when implementing the system for serious speed offenders.     

Operating cost based cruise speed reduction for ground delay programs: Effect of scope length

Ground delay programs typically involve the delaying of aircraft that are departing from origin airports within some set distance of a capacity constrained destination airport. Long haul flights are not delayed in this way. A trade-off exists when fixing the distance parameter: increasing the ‘scope’ distributes delay among more aircraft and may reduce airborne holding delay but could also result in unnecessary delay in the (frequently observed) case of early program cancellation. In order to overcome part of this drawback, a fuel based cruise speed reduction strategy aimed at realizing airborne delay, was suggested by the authors in previous publications. By flying slower, at a specific speed, aircraft that are airborne can recover part of their initially assigned delay without incurring extra fuel consumption if the ground delay program is canceled before planned. In this paper, the effect of the scope of the program is assessed when applying this strategy. A case study is presented by analyzing all the ground delay programs that took place at San Francisco, Newark Liberty and Chicago O’Hare International airports during one year. Results show that by the introduction of this technique it is possible to define larger scopes, partially reducing the amount of unrecovered delay.     

Extracting driving characteristics from heavy goods vehicle tachograph charts

European Union regulations require haulage companies of member states like the UK to keep records of their drivers’ hours of work. All heavy goods vehicles (HGV's) over 7.5 tonnes are fitted with tachographs which record a driver's operating activities (periods of driving, other work and rest). These records are etched onto a laminated chart by various styli, one of which records the vehicle's speed. This paper describes the development and testing of a new technique for extracting individual driving characteristics from the speed trace of an HGV tachograph chart to calculate four parameters: distance travelled, average speed, time travelled and speed variability.

The average speed, time travelled and speed variability were analysed statistically using one‐way analysis of variance tests. Speed variability was found to be particularly useful for identifying differences between individual driver's behaviour. Once differences in behaviours can be identified it may be possible to link certain driving habits to factors such as component wear, accident rates and excessive fuel usage.     

Decision Support Systems for Public Transport Management: The Athens Public Transport Authority Project

This article reports on an implementation study of a computerised decision support system for public transport management for the Athens Public Transport Authority (APTA). The study analysed the current situation, specified user requirements, determined system functionality, designed the system architecture, organised the project and, finally, planned dissemination activities. The decision support system covers the main public transport management activities of APTA - transport service provision, economic and financial planning, passenger complaints and suggestions, and personnel management - offering its users the possibility to study the potential effects of their decisions before implementation. To achieve this, the system will consist of a data warehousing system, for the integrated management of a wide variety of data sources, and of online analytical processing tools, for information analysis and scenario testing. The system architecture has been designed to offer robustness, flexibility, rich functionality and open connectivity. The system aims to help APTA reduce operational costs and provide a better transport service, attracting more passengers to public transport and reducing, in the process, congestion and pollution.