装配式综合管廊在地铁车辆基地中的发展及应用探讨

装配式综合管廊在地铁车辆基地中的应用尚处于探索阶段,为了将装配式综合管廊与地铁车辆基地有效结合,提出一种适合于地铁车辆基地的装配式综合管廊解决方案。系统研究车辆基地发展装配式管廊的可行性,从目前车辆基地综合管廊建设和运营现状出发,提出了单仓和双仓两种管廊断面模式。通过应用BIM技术对管线进行碰撞检查和节点深化设计,并在管廊设计中考虑相关附属配套设施。工程实践证明,装配式综合管廊比现浇管廊土建成本减少4%,工期缩短45%,从安全、环保、质量、工期、场地、运维等多方面具有明显优势,应大力推广。下阶段应从标准化设计、施工方面对装配式管廊进行系统研究并争取尽快应用到实际项目中。     

A planning tool for evaluating vehicles miles travelled and traffic safety forecasts of growth management scenarios: A case study of Baton Rouge and New Orleans

This study describes an adaptable planning tool that examines potential change in vehicle miles travelled (VMT) growth and corresponding traffic safety outcomes in two urbanized areas, Baton Rouge and New Orleans, based on built environment, economic and demographic variables. This model is employed to demonstrate one aspect of the potential benefits of growth management policy implementation aimed at curbing VMT growth, and to establish targets with which to measure the effectiveness of those policies through a forecasting approach. The primary objective of this research is to demonstrate the need to break with current trends in order to achieve future goals, and to identify specific policy targets for fuel prices, population density, and transit service within the two study regions. Models indicate based on medium growth scenarios, Baton Rouge will experience a 9 percent increase in VMTs and New Orleans will experience 10 percent growth. This translates to corresponding increases in crashes, injuries and fatalities. The paper provides forecasts for planners and engineers to consider an alternative future, based on desired goals to reduce VMTs and therefore improve safety outcomes. A constrained-forecast model shows a cap on VMTs and crash rates is achievable through policy that increases fuel prices, population density and annual transit passenger miles per capita at reasonable levels through a growth management approach.     

流线型钢箱梁涡激振动机理与气动控制措施

以某主跨390 m的独塔流线型钢箱梁斜拉桥为工程依托，采用风洞试验与计算流体动力学（Computational Fluid Dynamics，CFD）相结合的方法对流线型钢箱梁涡激振动机理与气动控制措施进行研究。首先，采用几何缩尺比为1∶30的主梁节段模型进行主梁涡振性能与气动控制措施优化研究；其次，采用CFD方法对主梁涡振响应进行流固耦合计算，将Newmark-β算法嵌入ANSYS Fluent用户自定义函数（User Defined Functions，UDFs）实现主梁结构振动响应求解，同时结合动网格技术实现主梁断面流固耦合分析；并根据判断条件来检索箱梁壁面上的网格单元，以获得主梁断面振动过程中的表面压力，然后结合主梁结构振动响应、表面压力以及流场特征等对主梁涡激振动机理进行分析。结果表明：该桥主梁原设计方案存在涡激共振现象，将梁底检修车轨道内移120 cm可有效抑制主梁涡振响应；主梁涡激振动响应的数值模拟结果与风洞试验结果吻合较好；检修车轨道内移120 cm后主要改变了箱梁下表面平均压力系数分布特性，且箱梁表面各测点脉动压力卓越频率不一致，有效减小了主梁涡激振动响应；流线型箱梁靠近迎风侧的“被动区域”对结构涡振响应贡献较小，背风侧“驱动区域”发生周期性旋涡脱落是影响流线型箱梁涡振的主要因素。     

Interactive travel choices and traffic forecast in a doubly dynamical system with user inertia and information provision

This study models the joint evolution (over calendar time) of travelers’ departure time and mode choices, and the resulting traffic dynamics in a bi-modal transportation system. Specifically, we consider that, when adjusting their departure time and mode choices, travelers can learn from their past travel experiences as well as the traffic forecasts offered by the smart transport information provider/agency. At the same time, the transport agency can learn from historical data in updating traffic forecast from day to day. In other words, this study explicitly models and analyzes the dynamic interactions between transport users and traffic information provider. Besides, the impact of user inertia is taken into account in modeling the traffic dynamics. When exploring the convergence of the proposed model to the dynamic bi-modal commuting equilibrium, we find that appropriate traffic forecast can help the system converge to the user equilibrium. It is also found that user inertia might slow down the convergence speed of the day-to-day evolution model. Extensive sensitivity analysis is conducted to account for the impacts of inaccurate parameters adopted by the transport agency.     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

A new model for temporal–spatial stochastic analysis of vehicle–track coupled systems

The vehicle–track coupled system has a random nature in the time–space domain. This paper proposes a computational model to analyse the temporal–spatial stochastic vibrations of vehicle–track systems, where the vehicle–track system is divided into a vehicle subsystem, track subsystem, and interfacial subsystem between the wheel and rail. In this model, the time-varying randomicity of dynamical parameters of the vehicle system, correlation, and randomness of the track structural parameters in the time–space joint dimensions, and randomness of the track random irregularities are considered. A probability dimension-reduction method was used to randomly combine different random variables. Furthermore, the probability density evolution method was applied to solve the delivery problem of probabilities between excitation inputs and response outputs. The temporal–spatial stochastic vibrations of the vehicle–track system with different coefficients of variation were studied, in which we assumed that the dynamic parameters obeyed the normal distribution, and the stochastic simulation method of the track random irregularities is probed into. The calculated results from this model are consistent with the actual measured results and physical conceptions. Thus, the temporal–spatial stochastic evolutionary mechanism can be explored, and the limits of dynamic indices can be formulated by using this developed model.     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

Insights into vehicle trajectories at the handling limits: analysing open data from race car drivers

Race car drivers can offer insights into vehicle control during extreme manoeuvres; however, little data from race teams is publicly available for analysis. The Revs Program at Stanford has built a collection of vehicle dynamics data acquired from vintage race cars during live racing events with the intent of making this database publicly available for future analysis. This paper discusses the data acquisition, post-processing, and storage methods used to generate the database. An analysis of available data quantifies the repeatability of professional race car driver performance by examining the statistical dispersion of their driven paths. Certain map features, such as sections with high path curvature, consistently corresponded to local minima in path dispersion, quantifying the qualitative concept that drivers anchor their racing lines at specific locations around the track. A case study explores how two professional drivers employ distinct driving styles to achieve similar lap times, supporting the idea that driving at the limits allows a family of solutions in terms of paths and speed that can be adapted based on specific spatial, temporal, or other constraints and objectives.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.