大功率整流器换流问题研究

理论上分析了大功率整流电路换流过渡过程，分析了换流过电压、关断功率与阻尼电路参数间的相互关系，提出换流过电压和关断功率的计算方法与计算公式，进一步探讨了如何合理配置阻尼保护电路参数。特别指出在大电流瞬时关断功率比换流过电压具有更大的危害性。为消除元件在换流过程中的关断损坏，还推荐一种改进型整流电路。     

VoIP中的丢帧补偿策略研究的概况

VoIP由于其分组交换方式及实时性特点,不能保证分组的可靠传输.阐述了造成VoIP质量不高的原因,比较了几种丢帧补偿策略的优缺点,介绍了G.723.1的插值补偿算法.     

Prediction of fatigue life and estimation of its reliability on the parts of an air suspension system

Air suspension systems have been implemented in various commercial vehicles, such as buses and special purpose trucks, because of the comfortable ride and easy height control. An evaluation of the durability of vehicle parts has been required for service life and safety starting in the early stages of design. The cyclic load applied to the vehicle can cause fatigue failure of parts, such as the suspension frame. This paper presents a method to predict the fatigue life of the suspension frame at the design stage of the air suspension system used in a heavy-duty vehicle. To estimate the fatigue life using the SN method, the Dynamic Stress Time History (DSTH) is necessary for the part of interest. DSTH can be obtained from the results of the flexible body dynamic analysis using the Belgian road simulation and the Modal Stress Recovery (MSR) method. Furthermore, the reliability of the predicted fatigue life can be evaluated by considering the variations in material properties. The probability and distribution of the expected life cycle can be obtained using experimental design with a minimum number of simulations. The advantage of using statistical methods to evaluate the life cycle is the ability to predict replacement time and the probability of failure of mass-produced parts. This paper proposes a rapid and simple method that can be effectively applied to the design of vehicle parts.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

终端区飞机排序的混合人工鱼群算法

为了保障飞行安全,对终端区着陆飞机进行有效的排序,建立了以航班延误总时间最小为目标函数的规划模型,以人工鱼群算法为基础,融合了遗传算法的选择操作和模拟退火算法的依概率接受的思想,形成混合人工鱼群算法,对着陆飞机排序问题进行了仿真计算,并与先到先服务算法、模拟退火算法以及蚁群算法进行了对比研究。仿真结果表明:与先到先服务相比,使用人工鱼群算法使得单跑道、双跑道延误分别减少了9·3%和48·0%,计算时间小于3s;与蚁群算法和模拟退火算法相比,求解的延误与时间最小,因此,提出的混合算法可行。     

基于有机朗肯循环的车用柴油机排气余热回收系统性能分析

利用设计的有机朗肯循环系统回收某重型车用柴油机的排气能量,通过台架试验,获得了变工况下柴油机排气余热能分布特性。分析了有机工质蒸发压力、过热度以及柴油机工况变化对有机朗肯循环系统性能的影响,以系统净输出功率和热效率为优化目标,确定了适用于有机朗肯循环系统的最佳蒸发压力。研究结果表明,当有机工质蒸发压力为1.8 MPa时,有机朗肯循环系统的净输出功率最大可以达到12.69kW,热效率可以达到11.19%;将有机工质加热至过热状态并不能明显提高有机朗肯循环系统的净输出功率。     

功率回收方式在大流量油泵、油马达试验系统中的应用

试验分析两种功率回收方式在大流量油泵、油马达系统中的应用,阐述两种功率回收系统的原理,计算两种试验系统的设备动力系数,分析了功率回收试验系统的应用前景。     

探地雷达技术在岩溶地质勘探中的应用

以新建田德线初勘探地雷达实测结果为依据,分别从探测原理、技术方法、成果分析这几个方面,探讨了在岩溶异常发育地区,如何发挥探地雷达的工程物探技术的作用。运用探地雷达技术,探查并圈定了溶蚀破碎、溶洞、溶沟、溶槽等岩溶地质异常范围。     

Preloading of independent leg units at locations with difficult seabed conditions

This paper, based on analyses of case histories, reviews soil conditions causing sudden uncontrolled leg penetrations, together with site data needed to plan safe installations of jack-up drilling units. Punch-through-like failure in uniform clay profile is analysed. Preloading procedures aimed at minimizing potential damage to the unit are suggested and discussed.