Experimental Study on Mechanical Behaviors of Prefabricated Column-Base Joint with Grouted Sleeves Connecting Longitudinal Reinforcements in Tunnels北大核心CSCD

In recent years, large shield tunnels with internal double-decked lanes have been developing rapidly in the field of highway tunnels, and prefabricated elements are increasingly adopted in internal structure. Based on the columns-base joint in Zhuguanglu tunnel, which is under construction, 2 full-scale specimens are designed for the quasi-static test, one specimen is connected with grout sleeve splicing and the other is cast in place. The test results show that: the bearing capacity of specimen with grout sleeve splicing is equal to that of cast-in-situ specimen, but its ductility and energy dissipation capacity are worse than that of the cast-in-situ specimen. And for the specimen with grout sleeve splicing, there exists crack concentration on the area above the sleeve. The crack width is too larger in this area. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Characteristics and Development Trends of the Support Technology of High Ground Stress Tunnels in China北大核心CSCD

Combining the present situation and development trend of different tunnel support technologies at home and abroad, this paper analyzes the problems of rockburst in hard rock tunnels and large deformation in soft rock tunnels caused by high ground stress. It is concluded that: 1) regarding the rockburst problem, the current support technology is mainly influenced by the rock burst mechanism which is dominated by static factors, and so the used support components are generally of smaller deformation performance and "passive support" properties; 2) as the rockburst is the result of dynamic-static stress coupling, and only the anchor bolt has the "active support" attribute in the current "shotcrete+anchor bolt+wire net" support system, so the best support system should have the two functions of active support and energy release in terms of the rockburst problem, and the key focus of the research and development is anchorage members; 3) there are three main support types for large deformation in soft rock tunnels, e.g. the heavy support, layered support and yielding support. Among them, the heavy support system in underground cavern with large deformation is easy to induce excessive surrounding rock pressure, and so the applicable conditions are limited. The layered support system is still not the best choice due to its immature theoretical study, difficult determination of the thickness value and the installation time of each support layer and the interference to construction progress. With the characteristics of timely support and yielding while supporting, the yielding support system can give full play to the performance values of surrounding rocks and supporting materials, and make both of them reach the optimal state, so it is the best choice for supporting the soft rock tunnels with large deformations. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Formulating cargo inventory costs for liner shipping network design

This study examines how to incorporate the inventory costs of containerized cargoes into existing liner service planning models such that the designed networks could be improved while not causing extra modeling/computational burden. Two approaches are compared: (i) not considering the inventory costs at all and (ii) incorporating the inventory costs associated with onboard time and those related to transshipment by assuming a fixed connection time. The two models are compared with the ideal model capturing the exact inventory costs on a route choice problem and a capacity planning problem based on extensive randomly generated and practical numerical experiments. The results show that: first, ignoring the inventory costs in service planning models may lead to network design with much higher costs (poor network design decisions); second, in service planning models assuming weekly frequency, the inventory costs associated with onboard time could be formulated exactly, and those related to the connection time of weekly services could be approximated by assuming fixed connection time of 3.5 days for ports with 1 day’s minimum connection time and 4.5 days for ports with 2 days’ minimum connection time.     

船舶液压起重机延迟反馈吊重消摆控制

由于操纵和工作环境的变化,起重机的吊重在工作过程中会产生摆动,这种摆动降低了起重机的工作效率和安全性能。文章以集美大学轮机工程实验中心船舶液压起重机为研究对象,采用机电液仿真建模技术及拉格朗日方程,在MATLAB Simulink仿真软件平台上,建立起重机操作液压系统及吊重摆动模型,采用与试验数据对比的方法对所建立的模型进行验证。设计基于吊重摆动位置延迟反馈的控制器,通过将延迟反馈信号叠加到操作信号上的方法实现吊重的消摆控制。结果表明,在各种操作情况下,延迟反馈控制器均能很好地抑制吊重的摆动。     

The Bid-rent Land Use Model of the simple,efficient, elegant,and effective model of land use and transportation

Integrated land use/transportation forecasting models add significant policy and infrastructure alternatives analysis capabilities to the urban planning process. The financial, time, and staff requirements to develop these models has put them beyond the reach of most small to medium sized urban areas. This paper presents the land use allocation submodel of the Simple, Efficient, Elegant, and Effective model of land use and transportation (SE³M), an integrated land use and transportation forecasting model founded upon Economic Base Theory and Bid-rent Theory. The Bid-rent Land Use Model (BLUM) is an agent based, spatial competition model utilizing unique utility curves for willingness to pay and incomes for budget constrained abilities to pay for each agent. The model structure, estimation, calibration, implementation, and validation are presented. With a single year of land use data available, the validation approach used the Kappa Index of Agreement to spatially check model outputs against base year control data while controlling for agreement by chance. The U.S. territory of Guam is used as the case study/proof of concept implementation for this model framework. Once calibrated, BLUM could solve the spatial competition problem on Guam in less than two minutes of processing time with over 90% accuracy.     

Assessing the impact of reduced visibility on traffic crash risk using microscopic data and surrogate safety measures

Due to the difficulty of obtaining accurate real-time visibility and vehicle based traffic data at the same time, there are only few research studies that addressed the impact of reduced visibility on traffic crash risk. This research was conducted based on a new visibility detection system by mounting visibility sensor arrays combined with adaptive learning modules to provide more accurate visibility detections. The vehicle-based detector, Wavetronix SmartSensor HD, was installed at the same place to collect traffic data. Reduced visibility due to fog were selected and analyzed by comparing them with clear cases to identify the differences based on several surrogate measures of safety under different visibility classes. Moreover, vehicles were divided into different types and the vehicles in different lanes were compared in order to identify whether the impact of reduced visibility due to fog on traffic crash risk varies depending on vehicle types and lanes. Log-Inverse Gaussian regression modeling was then applied to explore the relationship between time to collision and visibility together with other traffic parameters. Based on the accurate visibility and traffic data collected by the new visibility and traffic detection system, it was concluded that reduced visibility would significantly increase the traffic crash risk especially rear-end crashes and the impact on crash risk was different for different vehicle types and for different lanes. The results would be helpful to understand the change in traffic crash risk and crash contributing factors under fog conditions. We suggest implementing the algorithms in real-time and augmenting it with ITS measures such as VSL and DMS to reduce crash risk.     

Direct formulation and algorithms for the probit-based stochastic user equilibrium traffic assignment problem

This paper proposes simple and direct formulation and algorithms for the probit-based stochastic user equilibrium traffic assignment problem. It is only necessary to account for random variables independent of link flows by performing a simple transformation of the perceived link travel time with a normal distribution. At every iteration of a Monte-Carlo simulation procedure, the values of the random variables are sampled based on their probability distributions, and then a regular deterministic user equilibrium assignment is carried out to produce link flows. The link flows produced at each iteration of the Monte-Carlo simulation are averaged to yield the final flow pattern. Two test networks demonstrate that the proposed algorithms and the traditional algorithm (the Method of Successive Averages) produce similar results and that the proposed algorithms can be extended to the computation of the case in which the random error term depends on measured travel time.     

Impact of regional population density on walking behavior

Land use can influence walking (measured by the number of steps) and so the health of people. This paper presents the result of empirical research on the impact of regional population densities (inhabitants per inhabitable area) on the number of steps (all steps, both outdoors and indoors). With data collected from almost 11,000 respondents in 148 Japanese regions, we estimate polynomial regression models, the total number of steps being the dependent variable and densities being the main independent variable. Regional population density significantly affects the number of steps after controlling for individual and household attributes. The estimated population density that maximizes the number of steps is around 11,000?persons/km². Increasing densities, up to levels of around 11,000?inhabitants/km², could increase walking and consequently the health of inhabitants. The population density elasticity of the number of steps is 0.046–0.049 in a simple log linear regression model without a peak.     

基于插补原理的船体复杂曲面加热线布置方法

船体曲面成形技术是船舶加工过程中重要的环节。如何更好更快实现船体复杂曲面加工,一致以来备受国内外学者的关注。本文借鉴插补原理,对传统船体复杂曲面加热线布置进行了优化设计,得到了圆弧形板、s形板、帆形板和马鞍板的加热线。采用COMSOL Multiphysics多物理场仿真软件,分析四种加热线下钢板变形情况,并通过实验检验了插补形式下的船体曲面成形效果。结果表明：(1)插补算法得到的船体曲面加热线路程比传统加热线路程节约75%以上。(2)对有限元计算位移进行曲面拟合,得到的预测模型与实际船体曲面基本一致。(3)实验了四种曲面加热线,并将有限元预测位移与实验进行对比,二者误差在6%以内,有限元计算与实验结果基本吻合。该方法降低加工时间,提高加工效率。