高压齿轮泵浮动侧板的动态平衡机理

针对高压齿轮泵浮动侧板磨损问题,在解析齿轮泵内部流场的基础上重点研究了浮动侧板反推力作用点变化规律和导致侧板产生倾覆力矩的关键因素。以某型号高压大排量齿轮泵为模型,运用CFD软件解析齿轮泵内部流场并根据侧板结构特点建立压紧力和反推力的求解微分方程,求得一个轮齿啮合周期内的侧板倾覆力矩变化规律,同时通过建立齿轮泵工作腔压力测试系统对该理论分析结果进行验证,额定工况下：试验值与理论值误差为4.18%,当轮齿转角φ=14°时倾覆力矩达到最大值Ms=82.16N?m。该研究为高压大排量齿轮泵浮动侧板倾覆力矩计算和侧板结构优化设计提供了理论基础和技术支撑。     

船舶螺旋桨作用下直立式码头的护底流速计算

针对船舶螺旋桨对直立式码头的护底冲刷作用愈来愈严重,而我国的港口工程规范中缺乏该类设计的计算的问题,进行了螺旋桨作用下直立式码头的护底流速研究。采用国外各类规范以及相关文献的计算方法,以正在实施的科特迪瓦阿比让扩建项目一期工程为例,对比总结出直立式码头底部的护底冲刷流速的荷兰计算方法和德国计算方法,给直立式码头结构的护底设计提供依据。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

The impact of muddy bottoms in ports

Ports are drivers of regional and of countries’ economic development. Most ports are built close to coastlines, where waters are shallower and tend to suffer from deposit sedimentation processes, which reduce depths in operational areas. In presence of shallow waters and sedimentation, ports must decide whether to dredge or not, where both decisions have significant impacts on ports’ annual incomes. Nevertheless, there are seabeds, namely muddy bottoms, in which vessels can navigate with a safety degree. This paper aims at investigating the extent to which the theoretical knowledge of vessel’s control in muddy waters is valid at a certain nautical bottom, as defined by the Permanent International Association of Navigation Congresses (since 2009 the World Association for Waterborne Transport Infrastructure but the acronym stays PIANC) and its impact on port economics. To achieve the proposed objective, an email survey was sent to worldwide pilots that manoeuvre ships in muddy waters. The survey validated the theoretical knowledge, showed that navigation in muddy waters is possible, that it can contribute to reduce ports’ operational costs, and that the subject can be rather controversial.     

逆向支撑底模反吊在水中防撞墩台施工中的应用

在航道整治工程中设置的桥梁防撞墩,由于墩台的底部经常设置在常年平均水位之下,无法按常规方法采用底部模板正向支撑系统施工。通过采用逆向支撑底模反吊方案,将钢木组合整体模板吊装入水,墩台分层浇筑的方式进行施工。该方案无需设置围堰,形成干地施工条件,成功解决水下混凝土浇筑和模板拆除难的问题,也解决通航水域狭小、操作空间有限、保证正常通航的问题,具有施工方便、安全性高、墩台施工精度易于控制的优点。     

整治建筑物周边局部冲刷深度计算

针对现有局部冲刷深度经验公式多、适用范围小、计算结果与实际出入较大的问题,从冲刷机理上推导出通用的局部冲刷公式,并根据实际情况进行修正和确定相关参数。结果表明,整治建筑物周边局部冲刷深度主要与工前水深、工程前后流速变幅、水流紊动强度、流量调整情况等有关;冲刷公式中参数k、λ、n的取值对计算结果影响较大;修正后的公式与规范相比具有一定优势。     

板裂围岩结构弯曲失稳分析

文章分析了板裂结构地质背景及板裂介质岩体特征,研究了板裂围岩破坏模式及力学机理,并结合工程实例,利用随机有限元模型对板裂结构屈曲破坏进行分析。     

低周疲劳载荷下考虑累积塑性的船舶裂纹板剩余极限强度研究

研究表明在恶劣海洋环境中船体结构整体断裂破坏往往是低周疲劳破坏和累积塑性破坏的耦合结果。考虑这两者耦合作用的影响,评估船体结构的极限承载力更为实际。基于累积塑性和低周疲劳裂纹扩展,从理论上分析了平面内低周疲劳载荷下裂纹板的残余极限强度。经过一系列数值模拟,首先讨论低周疲劳裂纹扩展行为的影响,然后随着疲劳裂纹扩展的发展,主要讨论了初始变形,焊接残余应力,裂纹扩展长度,裂纹分布和裂纹板厚度对低周疲劳载荷下船体裂纹板极限强度的影响。     

砂桩排水板复合排水机理研究

目前复合排水地基固结度及强度无法从理论角度进行计算和预测,给工程设计及施工带来较大不便.针对这一问题,对砂桩排水板复合排水边界条件进行合理简化,推导出复合排水理论模型;并借助有限元软件PLAXIS 3D进行分析,将PLAXIS 3D计算结果与理论结果进行对比,并给出排水体控制区域不规则修正系数a的建议值.结果表明,理论模型计算结果与数值模拟结果相吻合;在砂桩间距大于3 m时,a值建议取1. 20～1. 35,当砂桩间距小于3 m时,a值建议取1. 35～1. 50.     

固结黏土地层盾构直接破除排水板关键技术研究

宁波地铁5号线1期下穿高速公路路基时存在68°斜交长40 m的含塑料排水板的固结黏土地层,为研究盾构直接通过可行性、刀具选型、施工参数优化等问题,利用TBM掘进模态综合试验平台,进行了不同类型刀具、不同掘进参数的固结黏土地层排水板破除试验。研究表明： 对于含排水板的固结黏土地层,在合理选择刀具、盾构参数并优化掘进参数情况下,盾构法施工直接破除基本可行,试验为宁波地铁工程建设提供了依据,也可为类似工程设计及施工提供参考。