车用液力变矩器的变形仿真研究

为确保液力变矩器的使用安全，对液力变矩器（空壳）在同一离心力场下的不同油压作用进行了实际工况仿真和有限元分析，通过对实际车用液力变矩器空壳的试验测试，结果表明液力变矩器颈端（Hub)和柄端（Pilot)的轴向变形与油压呈线性关系，理论计算值与试验测试结果吻合较好。     

液力变矩器焊接的数值模拟和质量控制

对液力变矩器的制造精和质量要求很高，焊后必须保证产品的尺寸精度，并要进行疲 试验以考虑焊缝的强度。通过分析计算，可以预测各种条件对焊接变形的影响；发现疲劳承载时的最危险断面在不在焊缝处，而是在上盖板的弯角处。     

A local model for the simulation of two–dimensional spilling breaking waves

A numerical model for the simulation of two dimensional spilling breaking waves is described. It is derived from a previous model which, in turn, takes its underlying ideas from the Cointe and Tulin theory of steady breakers. With respect to the former model, the present one is local, i.e., the inception, extension, and geometry of the breakers are determined through the local shape of the water surface. The model has been implemented in a RANSE code, which was developed for the simulation of ship flows, through a modification in the boundary conditions. This yields a simple and effective way to reproduce the breakers influence on the underlying flow. The resulting code has been used to simulate the flow past a submerged hydrofoil. The numerical results are compared with those of the previous model and with the experimental data obtained by Duncan.     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

铁路隧道松散破碎围岩塌方数值模拟分析

运用二维离散元程序UDEC3.1软件,对3种不同顶板岩性组合模型进行数值模拟,再现了隧道顶板岩层离层、弯曲、沉降、开裂直至塌方的全过程,分析了松散破碎围岩隧道塌方后围岩的位移、应力和塑性区分布特征。     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

基于数字信号处理的直接转矩控制研究

直接转矩控制因控制简单、具有优良的动静态特性，在电机控制中应用越来越广泛。但它在低速区的局限也较多。随着数字信号处（Digital Signal Processing，缩写DSP）技术的发展，使得改善其低速控制特性成为可能。文中简介了直棼转矩控制技术的特点、控制原理及难点，探讨了一种应用DSP技术的直接转矩控制方法。     

钩尾销螺栓折断的原因分析与探讨

分析了钩尾销螺栓折断的原因,并提出了改进建议。     

摆式车辆液压缸载荷的确定

详细介绍了摆式车辆液压倾摆系统的机构动作、车体复原力矩与液压缸脉冲加载时间的确定和液压缸载荷的计算。