高墩大跨径弯连续刚构桥梁空间非线性稳定分析

在高墩大跨弯连续刚构桥梁的设计与施工中,结构稳定性非常重要。本文分别考虑结构的几何非线性和材料非线性力学特征,对高墩大跨弯连续刚构桥梁的结构稳定性进行详细的数值分析,并与线弹性的计算结果进行对比。结果表明:弯连续刚构桥梁的稳定问题已经转化为考虑结构材料屈服强度的极限承载力问题,同时几何非线性对稳定的影响亦不能忽略。     

城市高架桥之高独柱墩横向位移探讨

结合城市高架高独柱墩顶部发生横向位移这一现象,对高独柱墩顶部横向荷载产生的原因进行初步分析,并应用三维非线性屈曲分析,阐述组合荷载所引起的大变形及混凝土徐变效应与墩顶横向位移之间的关系,提出了设计、施工类似结构时应注意的事项。     

大直径钢管桩承载力恢复过程试验研究

针对目前预制桩承载力恢复特性研究与工程应用中的不足,依托西非某海工工程,提出高应变法。采用对同一钢管桩进行初打与不同休止时间复打相结合的试验方法,研究了大直径钢管桩沉桩后的承载力恢复过程。结合地质情况、沉桩与试验结果,得到了钢管桩承载力、侧阻力及端阻力随时间变化的一般规律及影响因素,并通过静载试验对研究结果进行了验证。该研究在提高项目施工效率、降低成本的同时,还得到了有意义的规律与结论,可为后续类似项目提供参考。     

尼铁现代化项目中矩形空心桥台的优化设计

当前常用的时速200 km的铁路矩形空心桥台参考图中的桥台截面尺寸偏厚,安全富余量很大。为节约混凝土圬工量,希望在保证安全的前提下减少桥台截面尺寸。首先提出专门针对铁路矩形空心桥台台身截面计算的荷载图示,然后利用这一新的图示对拉伊铁路项目中使用的常规矩形空心桥台进行有限元分析,经过不断试算提出最优的截面尺寸。在钢筋用量基本不变的情况下,新尺寸桥台较原参考图中桥台的混凝土用量减少10%以上。对于项目所在地尼日利亚国水泥价格高昂的情况而言,桥台尺寸的这一优化将产生较大的经济效益。     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

成昆铁路矮塔斜拉桥索梁锚固区模型试验研究北大核心

为研究铁路矮塔斜拉桥索梁锚固区的受力形式,以成昆铁路金沙江大桥为工程背景,针对该桥采用的新型梁顶混凝土锚固构造,通过缩尺模型试验研究其在不同荷载下的应力分布和开裂特征。结果表明:在斜拉桥成桥恒载索力作用以及最不利荷载组合索力作用下,C7锚固块更容易发生破坏,将其作为试验构件开展缩尺模型试验,发现锚固块在不同张拉荷载作用下张拉至设计索力的过程中,应变增幅基本上线性增加,卸载后同样呈线性减小,说明混凝土受力处在线弹性阶段,且应力在规范要求范围内。在试验荷载加载至140%设计索力时,锚固块前端倒角位置开始出现细小裂纹且随荷载的增加不断开展。当荷载卸载至0时,之前出现的裂缝随荷载的减小逐渐闭合,宽度肉眼不可见,表明该构造能够满足正常使用要求且具备足够的安全储备。