多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

超深振捣条件下混凝土墙体模板侧压力的简化计算方法

超深振捣对混凝土成品质量有害无益,研究超深振捣引起模板侧压力增大的规律,可为规避其害提供依据。为此设计4个混凝土墙体试件,实测在浇筑过程中模板侧压力的变化情况。基于振捣液化和液体压力平衡理论,建立了超深振捣情况下混凝土模板侧压力计算模型,推导了计算公式,并与实验数据进行对比验证。研究结果表明,振捣深度是影响混凝土墙体模板侧压力的重要因素,本文提出的计算模型能很好地预测墙体结构超深振捣位置的模板侧压力。     

西南红层软岩地区铁路滑坡形成机理分析及治理措施

红层软岩地区铁路工程建设中滑坡问题突出。本文结合西南地区一铁路红层滑坡治理工程,利用该地区红层滑坡的现场调查结果,从红层软岩特性、地层岩性、地质地貌、水文地质条件、深孔位移监测数据等多方面对该地区铁路滑坡形成机理进行分析,并论述红层滑坡与一般滑坡的不同点,分析红层软岩岩体力学特性、地层主要成分以及红层软岩中的粉砂质泥岩在不同风化程度下的力学特性。根据分析结果提出治理措施,并对治理措施进行评价。总结得出地层岩性、地质水文、人为因素是导致红层滑坡病害发生的主要因素。     

格拉斯磁环匀强磁场分析

以毕奥-萨伐尔定律为基础,建立亥姆霍兹线圈以及格拉斯磁环中心磁场分布模型,并计算了它们内部的轴向磁感应强度分布,绘出了空间分布图,分析了轴向磁感应强度与x、y坐标的关系,分析结果得到了亥姆霍兹线圈和格拉斯磁环内部匀强磁场分布区域,通过比较得到格拉斯磁环内部的匀强磁场区域比亥姆霍兹线圈内部的匀强磁场分布区域更大的结论。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

城市轨道交通钢轨电位和新型回流装置研究

以成都地铁为例,基于钢轨绝缘节的老化和单向导通装置频繁导通问题,将车辆段及停车场等效为小电阻接地支路进行仿真。仿真结果表明,小电阻接地支路可使正线钢轨电位最大提升27.2 V,威胁了正线的安全运营。据此提出一种应用于车辆段与停车场的新型钢轨回流装置,并介绍其控制方法。该新型钢轨回流装置具有辅助列车安全通过绝缘节遏制车辆段与停车场内杂散电流、评估钢轨绝缘节绝缘性能和测量出入段线钢轨过渡电阻的功能。     

计及叶片载荷的双机对转式海流发电机系泊系统动力分析

本文设计了一种新型的双机对转式海流发电机并对其系泊系统与叶片载荷和直径关系进行模拟分析。首先将单机式海流发电机与已有研究进行对比验证其可靠性，然后在不改变系泊方式的前提下，设计出双机式结构，并通过分析机身位移和旋转比较两种系统的稳定性。为考虑叶片载荷对系泊系统影响，在Orcaflex中对不同精细程度的叶片进行建模，分别对比单一翼型/三翼型/九翼型的数值模拟结果。接着使用M-BEMT软件优化后的翼型参数，对比使用原始升阻力系数的三翼型发电机的模拟结果，同时将使用不同直径叶片的发电机系统进行对比，说明双机式发电机的稳定性更优，对海流发电机及其系泊系统的设计提供重要参考价值。     

某型直流充电柜温度场仿真

对某型直流充电柜满负载工况下温度场进行仿真,根据实验测量数据验证仿真结果准确性,成功完成了对充电柜温度场的建模仿真工作,并实现对初始模型的简化,为对整个充电站进行温度场建模仿真奠定了基础。     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

VVL耦合喷油策略对GDI汽油机混合气形成的影响

利用三维仿真软件Ansys Fluent建立了GDI汽油机的仿真计算模型,就变气门升程耦合不同喷油策略对缸内气流运动和混合气形成的影响进行了模拟计算。结果表明,与大气门升程工况相比,小气门升程工况的缸内湍流运动强度、燃油蒸发和湿壁情况以及点火时刻混合气质量都明显改善;在小气门升程工况,采用两段喷油会缩短油气混合时间,过度推迟二次喷油时刻会恶化混合气质量和燃油湿壁情况;在大气门升程工况,两段喷油会改善混合气均匀性,随着二次喷油时刻推迟,燃油蒸发量增加,湿壁情况加剧,混合气质量得到改善;小气门升程工况下采用二次喷油时刻为470°曲轴转角,前后两次喷油量比例为7∶3的两段喷油方案在燃油蒸发和湿壁以及点火时刻缸内混合气质量这几个方面的效果都很好,是最合理的方案。