光学仪器法快速找寻轴系理论中心线的研究

舰船轴系装调过程中,理论中心线的确定方法有多种。本文采用光学仪器法快速找寻轴系理论中心线,理论支持性强,高效而独特,具有较强的实用性。     

土工格栅在治理沥青路面裂缝中的应用

裂缝是沥青路面常见病害。应用非织造土工织物——多功能双向土工格栅治理高等级公路沥青路面的裂缝,取得了良好的效果,并对土工格栅的应用进行了定量计算。     

石河道大桥桩基础施工

针对卵石地层桩基础成孔问题,根据石河道大桥实际施工实践介绍了应用冲击钻孔的方法加以解决的施工方法,并着重分析了该方法的工艺流程和内容,以及施工中的注意事项.     

往复式压缩机系统的管道振动分析

从动力分析角度，通过对往复式压缩机引起管道振动原因的分析，提出控制管道振动的方法；以海上已投产平台管道布置为例进行振动分析，通过计算管道因脉动引起管道振动的不平衡力，确定抑制管道振动的最佳方法。     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

海上单桩风力发电平台简化设计

采用在欧洲已经进行商业化运作的独立桩双段结构，桩基础采用带有过渡段的单桩。塔架上的风力发电机采用丹麦Vestas公司的V80风力发电机。参考DNV-OS-J101和API-RP-2A中的工作应力设计法，进行结构静力、桩基础的承载力，涡激振动、疲劳寿命，结构动力学等分析。静力分析分析极端环境下的组合工况；桩基础主要计算桩的轴向承载力和校核水平承载力，并采用有限元模型模拟桩土相互作用；涡激振动分析主要考虑不同风速下塔架的升力以及引起的横向振动；疲劳分析根据涡激振动分析的结果利用S-N曲线对基础寿命进行了评估；动力学分析求出了结构的固有频率，并进行了波浪力作用下的瞬态历程分析。     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

京秦线提速路涵过渡段动力仿真与试验对比

结合京秦线提速改造工程进行了列车 路基动力仿真计算。在不同速度条件下,通过对路涵过渡段加固前后状态下机车车辆运行安全舒适性指标、轨道及路基主要动力性能指标的分析计算,对京秦既有线路涵过渡段提速到200km/h的适应性及加固方案的可行性提出了相应评价意见与建议,并与随后的实车试验进行了对比。试验测试结果验证了仿真分析的可靠性。