爆炸硬化高锰钢组合辙叉水平裂纹伤损分析

爆炸硬化高锰钢组合辙叉是近几年针对重载铁路使用条件开发的一种新型固定型辙叉产品,在批量上道使用后,水平裂纹伤损发生频次逐渐增加,引起广泛的关注。对水平裂纹伤损产生的原因进行分析,并提出多项改进措施。通过改进措施的实施,在朔黄线取得了较好的改进效果。实际结果表明,通过不断改进工艺、提高质量、加强维护,爆炸硬化高锰钢组合辙叉能够实现通过总重3亿t以上的目标。     

新城区轨道交通线路规划关键问题研究

对国内外主城与新城衔接的新城区(郊区)轨道线特征及交通功能等因素进行总结分析，并结合武汉市及国内外典型城市新城区轨道交通规划建设经验，对新城区轨道交通线路规划关键问题做深入研究。提出对新城区轨道交通线路规划中与其他不同层次轨道线网功能及技术标准的衔接关系；与新城区发展应注重以轨道交通引领新城区协同发展，与城市空间结构高度契合关系；新城区轨道线路走向应沿预测主要客流走廊，串联新城区商业、交通枢纽等大型客流集散点，以缓解开通初期普遍面临客流量增长缓慢，客运强度偏低的问题。     

重载货车摩擦缓冲器阻抗特性的数值模拟

为预测摩擦缓冲器的实际工作状态,从几何特征和作用原理的角度,建立详细的MT-2型缓冲器理论模型。首先,通过对缓冲器内部各摩擦元件的运动学和静力学分析,推导出缓冲器在准静态下的阻抗特性;其次,引入附加摩擦系数量化各摩擦元件之间动静态摩擦过渡时的黏滞补偿,并模拟出缓冲器在动态下的阻抗特性;最后,利用C80型货车冲击试验数据对该缓冲器的理论模型进行验证。验证结果表明:总体上,数值模拟和现场试验下的缓冲器示功曲线基本吻合,说明模型的正确性;局部上数值模拟中缓冲器从加载Ⅰ阶段过渡至加载Ⅱ阶段的突变现象在冲击试验中表现的并不明显,还有待进一步完善。     

城市轨道交通全自动运行线路在无人值守模式下的应急处置

基于不同的场景,详细阐述了无人值守模式下全自动运行线路的应急处置方法、区间疏散方式及救援方式。结合专门的自动应急或远程应急功能,使无人值守全自动运行线路应急处置能兼顾运营效率和安全,避免列车迫停区间。建议做好多职能队员的相关培训工作,并合理选择列车自动运行控制系统的应急功能。     

基于云平台的城市轨道交通能源管理系统

阐述了基于云平台的城市轨道交通能源管理系统架构和建设方式。该系统利用云计算的高效和弹性来部署建设,采用线网-车站二层管理模式,降低了线网和线路服务器等的硬件部署成本和维护成本。通过将能源管理系统内部使用的业务应用转换为基于云平台的能源管理应用软件,能源管理系统可获取云平台提供的共享数据,并将经过业务处理后的数据存储到云平台中,以服务于云平台上其他业务,实现了数据资源的逻辑统一和高效利用。     

基于OWA与灰色聚类的城市轨道交通PPP融资风险评价方法研究

针对城市轨道交通PPP融资成本高、投资回收期长、不确定性因素多等特点导致整个融资过程充满风险,且难以进行科学的评价,进而增加风险评价难度的问题,提出基于OWA与灰色聚类的城市轨道交通PPP融资风险评价方法。首先从全寿命周期角度构建城市轨道交通PPP融资风险指标体系。然后基于OWA算子对专家决策数据按照降序的方式重新排序,消除极值带来的不利影响,加权得出指标的权重值。最后考虑指标的灰色性、信息不完整性,构建灰色白化权函数实现指标信息的透明化,完成对PPP融资风险的聚类分析。应用构建的模型对郑州地铁1号线一期工程PPP融资风险进行评价,认为该地铁工程PPP融资风险等级高,应重点关注前期策划、社会资本、政策环境、设计质量、成本超支、建设质量、残值7个主要风险指标的控制,以期为该项目融资风险管理提供建议,并进一步丰富城市轨道交通PPP融资风险的评价方法。     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

超高压共轨系统轨压控制策略研究

为稳定控制超高压共轨系统中的共轨腔压力并缩短轨压控制算法的开发周期,利用AMESim/Simulink联合仿真技术建立了超高压共轨系统轨压控制仿真模型,采取前馈+PID控制算法设计了轨压控制策略,并针对轨压控制中的瞬态和稳态工况进行了仿真计算,最后在试验台架上开展了轨压跟随性测试。结果表明:所制定的前馈+PID控制算法能使轨压稳定在目标轨压附近,上下波动小于3 MPa,且轨压突变时瞬态响应时间小于0.5s,控制结果能够满足超高压共轨系统对精度和速度的需求。