重型卡车驾驶室造型趋势研究

本文从整体造型风格、造型轿车化以及信息化、智能化对造型的影响等方面探讨了当代重型卡车车身造型设计的发展趋势.     

计及导向摆臂约束的重型货车驾驶室俯仰平面动力学模型

传统的重型货车驾驶室俯仰平面动力学模型没有考虑悬置导向机构的影响,仅能粗略计算驾驶室垂向和俯仰响应,无法计算驾驶室质心的纵向振动特性,因而其仿真精度较低,且在实际工程应用中受到了限制.为提高模型精度并拓宽其工程应用范围,创建了考虑导向摆臂约束作用的驾驶室俯仰平面动力学模型,分析了摆臂导向机构的约束特性.在此基础上,通过...     

Influence of AC system design on the realisation of tractive efforts by high adhesion locomotives

The main task for heavy haul railway operators is to reduce the cost of exported minerals and enhance the long-term viability of rail transport operations through increasing productivity by running longer and heavier trains. The common opinion is that this is achievable by means of implementation of high adhesion locomotives with advanced AC traction technologies. Modern AC high adhesion locomotives are very complex mechatronic systems and can be designed with two alternative traction topologies of either bogie or individual axle controls. This paper describes a modelling approach for these two types of AC traction systems with the application of an advanced co-simulation methodology, where an electrical system and a traction algorithm are modelled in Matlab/Simulink, and a mechanical system is modelled in a multibody software package. Although the paper concentrates on the analysis of the functioning for these two types of traction control systems, the choice of reference slip values also has an influence on the performance of both systems. All these design variations and issues have been simulated for various adhesion conditions at the wheel–rail interface and their influence on the high traction performance of a locomotive equipped with two three-axle bogies has been discussed.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

对软弱地基加固处理的试验研究

针对武汉阳逻国际集装箱陆域码头工程的特点，采用塑料排水板的方式对软弱地层进行处理，对于其上的堆载（吹填砂）采用强夯的方式进行加固。通过现场试验表明，此种加固处理效果很好，为软弱地基加固处理提供了科学依据。     

Bolster spring fault detection strategy for heavy haul wagons

An on-board health monitoring system is proposed for heavy haul wagons in this paper including a signal-based fault detection and isolation (FDI) method and an on-line fault diagnose strategy. Such a system, to be feasible on freight wagons, must be sufficiently cheap and robust, hence the design assumes the constraint of using only two accelerometers mounted on the front left and right rear part of each carbody in a heavy haul train. This paper focuses on the detection of bolster spring fault conditions. The problem is made more complex by the modes of failure which might be expected in bolster spring nests. Types of spring failure are firstly identified and discussed covering situations of broken (shortening springs) and softening (individual spring loss from a nest or cross-section loss through corrosion). The effects of these faults and their detectability were investigated using simulations on straight and curved track and using a fully detailed model of a typical 40?t axle-load heavy haul wagon. The simulation results were then examined and compared using cross-correlation analysis and an FDI system was proposed. The FDI system introduced five possible fault indicators. Initial results indicated that it was possible to detect changes in bolster stiffness of ±25%. An on-line fault diagnoses strategy is proposed for bolster spring faults which only requires data from wagon monitoring during travel around sharp curves to detect and the occurrence of confirm faults. The functionality envisaged needs only a ‘once per trip’ monitoring site, such as a sharper curve, and is aimed at condition monitoring rather than the provision of alarms or comprehensive monitoring of all events.     

重庆朝天门长江大桥施工控制压重方案设计

朝天门长江大桥全长932 m,主桥为(190+552+190)m三跨连续单拱钢桁梁。结合主跨合龙特点介绍主跨合龙的思路、计算及操作要点,应用大型有限元分析程序MIDAS建立了朝天门长江大桥的三维有限元简化计算模型,并对其进行了施工过程控制分析。压重方案设计可以为同类桥梁的施工控制分析提供有益的思路。     

山西省重载水泥混凝土路面结构设计与体会

对山西省已建成的几条重载水泥混凝土路面高速公路结构进行汇总分析,并结合重载交通的特性和典型病害,提出了一些结构设计体会,供同行参考。     

Modeling Feedback Scheme of Empty Cars in Unloading End of Heavy Haul Railway

The transportation organization of heavy haul railway is complex in China, especially, the feedback of empty cars. On the basis of reference to the existing research results, and deep analysis of the characteristics of empty cars distribution of heavy haul railway, the authors construct the feedback schematic model of empty cars in unloading end of heavy haul railway. The minimum quantity of the combined trains and the time for combination is taken as the model goal and solution algorithm on the basis of minimum cost and maximum flow is formulated. Daqin railway is taken as an example and relevant conclusions of feedback scheme of empty cars of heavy haul railway, through an analysis of calculation results, are drawn.     

大风浪中航行船舶的危险度估算模型

根据风险分析理论,结合模糊综合评定数学模型,提出了一种对大风浪中航行船舶的危险度进行定量估算的模型。在进行了大量的专家问卷调查后,得到了客滚船“燕京”轮在大风和大浪的作用下,可能发生不同等级事故的模糊关系矩阵,对该轮在大风浪中的不同航行方案进行了危险度的实际计算。结果显示,当该轮遇到大风浪时,按正常航线行驶,发生事故的风险度较大;按习惯的北上避风方案绕航,风险度最小;而按以上两方案的折衷方案行驶,有较大风险。此方法可以较好地对船舶在大风浪中的危险状况进行定量、直观地描述,可供船舶驾驶员和船舶安全管理者用来掌握大风浪中航行船舶的风险状况,进而有效实施风险决策。