潜艇悬停水舱排注水控制方式比较

为合理设计悬停水舱,根据理想气体状态方程,计算不同的注排水控制方式下的潜艇高压气体消耗量和舱室气压增量,采用定性分析的方法,比较不同的注排水控制方式在噪声水平及能耗两个方面的特点。结果表明,在潜艇日益重视减振降噪及在高压空气消耗量和舱室气压增量可以接受的情况下,悬停水舱选择能耗及噪声最低的气排注控制方式最为合理。     

采用微气泡缩减高速船拖曳阻力(英文)

Ship hull form of the underwater area strongly influences the resistance of the ship.The major factor in ship resistance is skin friction resistance.Bulbous bows,polymer paint,water repellent paint(highly water-repellent wall),air injection,and specific roughness have been used by researchers as an attempt to obtain the resistance reduction and operation efficiency of ships.Micro-bubble injection is a promising technique for lowering frictional resistance.The injected air bubbles are supposed to somehow modify the energy inside the turbulent boundary layer and thereby lower the skin friction.The purpose of this study was to identify the effect of injected micro bubbles on a navy fast patrol boat(FPB) 57 m type model with the following main dimensions:L=2 450 mm,B=400 mm,and T=190 mm.The influence of the location of micro bubble injection and bubble velocity was also investigated.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was precisely measured by a load cell transducer.Comparison of ship resistance with and without micro-bubble injection was shown on a graph as a function of the drag coefficient and Froude number.It was shown that micro bubble injection behind the mid-ship is the best location to achieve the most effective drag reduction,and the drag reduction caused by the micro-bubbles can reach 6%-9%.     

多功能疏浚作业辅助船研究与方案设计

多功能疏浚作业辅助船对保证挖泥船持续高效地作业非常重要,尤其是对在开敞海域中的疏浚工程更是直接影响到有效作业时间。介绍国外相关系列船型和欧洲四大疏浚公司对此类船的配置,总结此类船的特点,根据设计技术要 求,提出目标船的设计方案,分析或选择各种技术性能指标,并给出加装整平作业功能和射水疏浚功能的方案。     

基于高频方波注入的船舶电机无传感器控制研究

随着大功率交流调速技术的不断进步,船舶电力推进如今成为船舶行业的主要发展目标.为研究运行可靠稳定、灵活、高性能的船舶电机无位置传感器控制,系统采用高频注入法估算电机转子位置信号,根据基于高频注入永磁同步电机数学模型的研究,该系统中高频采用的是高频方波注入,减少滤波器的使用从而缓解了转子位置延迟现象,同时采用锁相环对电机转子的相位和频率跟踪来计算电机转子的估计转速,克服了估算转速脉动大的困难.利用Matlab对电机控制系统仿真,验证电机控制系统的电机转速平滑稳定,转子位置波形在0-2π有规律往返.最终实现高精度、灵活的无传感器船舶电机控制.     

南盘江特大桥钢管混凝土真空一次压注技术

根据云桂南盘江特大桥主桥上承式钢管混凝土拱桥的结构形式,钢管拱管内混凝土采用真空辅助一次压注顶升进行施工。介绍了管内混凝土采用真空辅助一次压注顶升的主要施工工艺和控制要点,为今后国内类似的大跨度钢管拱真空辅助一次压注施工积累了经验。     

喷孔位置对船用天然气发动机燃烧及排放影响的模拟研究

为了探究天然气与柴油喷孔位置对天然气发动机燃烧和排放的影响,基于L23/30天然气发动机,建立了柴油引燃天然气的发动机模型,利用CONVERGE软件对燃烧过程和排放进行模拟分析。模拟结果表明：由于天然气与柴油喷孔位置变化的影响,会导致柴油引燃天然气在空间的变化,因此对发动机的燃烧和排放造成了影响,通过对比不同喷嘴间的距离和不同喷嘴分布的设计方案得出,采用中心对称设计时获得了较好的燃烧和排放性能。     

An investigation of the performance of an electronic in-line pump system for diesel engines

WIT Electronic Fuel System Co., Ltd. has developed a new fuel injector, the Electronic In-line Pump （EIP） system, designed to meet China＇s diesel engine emission and fuel economy regulations. It can be used on marine diesel engines and commercial vehicle engines through different EIP systems. A numerical model of the EIP system was built in the AMESim environment for the purpose of creating a design tool for engine application and system optimization. The model was used to predict key injection characteristics under different operating conditions, such as injection pressure, injection rate, and injection duration. To validate these predictions, experimental tests were conducted under the conditions that were modeled. The results were quite encouraging and in agreement with model predictions. Additional experiments were conducted to study the injection characteristics of the EIP system. These results show that injection pressure and injection quantity are insensitive to injection timing variations, this is due to the design of the constant velocity cam profile. Finally, injection quantity and pressure vs. pulse width at different cam speeds are presented, an important injection characteristic for EIP system calibration.     

东风_4型机车柴油机压力波检测仪的应用分析

对压力波检测仪在机车检修中的具体使用方法、使用要求进行了论述,分析了大量的检测数据及压力波波形,总结了判断故障的经验方法,提出了4种典型故障的判别数据参考值及波形图样。     

A line impedance stabilization network for pulse current injection北大核心CSCD

［Objective］Aiming at the deficiency of the existing line impedance stability network (LISN) in the electromagnetic pulse protection capability, a LISN suitable for the pulse current injection (PCI) test of electrical and electronic equipment is proposed. ［Methods］Aiming at the characteristics of high peak value and fast rise of the pulse current in PCI testing, the circuit structure and physical structure of the LISN are improved on the existing basis through PSpice time-domain and frequency-domain simulation combined with engineering design requirements, thereby giving it good nanosecond pulse protection performance and impedance stability at the same time. Pulse current protection performance test and impedance curve test experiments are then designed and carried out.［Results］The experimental results show that the improved LISN can attenuate the injected pulse current by 60 times, while the error of its impedance curve is less than 5% compared with the Type 5 µH LISN in GJB 151B-2013. ［Conclusions］The proposed LISN has good impedance stability and decoupling ability, and can be used in the PCI testing of electrical and electronic equipment in order to protect the power supply and improve the repeatability of testing. © 2023 Chinese Journal of Ship Research. All rights reserved.     

船舶柴油机注汽涡轮增压系统

为了改善涡轮增压柴油机在低工况运行时,会出现增压压力不足、燃烧过量空气系数小和废气排温较高等固有特性,提出了一种利用增压器废气余热产生水蒸汽,并注入涡轮来提高增压器的压比和空气量的新方法。这种新方法可以改善涡轮增压器与柴油机的匹配,从而可提高柴油机的性能。试验结果证实了该方法的有效性。