全液压推土机关键技术参数研究

研究了全液压推土机的关键技术参数———滑转率、效率、牵引比和比功率。通过分析牵引效率在滑转曲线上的配置,给出了全液压推土机的额定滑转率为12%～15%。从理论和试验两个方面深入分析了压力和排量对泵—马达系统效率的影响,得到了典型泵—马达效率的试验数据拟合公式。在对全液压推土机驱动系统的匹配目标设计时,除了满足扭矩和功率上的匹配要求外,还应考虑整机的效率。变量泵的变化范围最好控制在βp=0.4～1,变量马达的变化范围最好控制在βm=0.3～1,才能保证整机有较好的牵引性能。通过对典型全液压推土机的统计分析,确定牵引比均值为1.48,比功率为7.2kW/t,具体取值应该稍大于或等于该均值。     

汽车ABS滑模变结构控制的分析与仿真

汽车防抱制动系统(ABS)是改善汽车主动安全性的重要装置.本文介绍了滑模变结构控制方法,针对汽车ABS的特点利用此方法设计了控制器,并在MATLAB/Simulink的环境下进行了仿真,给出了仿真结果和评价.     

旧水泥混凝土路面注浆技术研究与实践

在水泥混凝土路面基础上加铺沥青混凝土路面时 ,对现有板块破损的处理十分关键 ,而其中又以板块的脱空处治为最。板底注浆是处理板块脱空常用且有效的方法 ,本文就注浆技术的原理、材料的选择、配比试验及施工实践等作了较详尽的介绍     

防抱制动系统基于模型的最佳滑移率计算方法

提出了一种基于μ-λ曲线的近似数学模型来实现最佳滑移率的递推最小二乘算法(RLS)。应用累积求和统计控制法(CUSUM)，解决了RLS算法在检测跃变路面时响应滞后的问题。通过计算机仿真，验证了算法在车辆防抱制动系统中的可行性和有效性。     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

Centrifuge modelling of pipe-soil interaction in clay with crust layer

Seabed in regions, such as the Gulf of Guinea and North West Shelf of Australia, may exhibit a crust layer where the undrained shear strength can be an order of magnitude higher than that of the immediately underlying sediment. This can complicate design of steel catenary risers, where fatigue depends on the cyclic vertical stiffness of the pipe-soil interaction. Potential punch-through of the riser into the underlying soft soil may invalidate design assumptions based on the pipe-soil stiffness within the crust layer. The long-term evolution of pipe-soil stiffness within the crust layer, which exhibits similar properties to an over-consolidated soil, is also poorly understood. This paper describes centrifuge model tests undertaken in a clay sample with a crust layer, simulating the punch-through process of a pipe under load control and investigating the pipe-soil stiffness during long-term cyclic loading tests under displacement control. Results confirm that the potential for punching-through the crust layer depends strongly on the relative ratio of pipe diameter to crust layer thickness. The long-term evolution of pipe-soil stiffness showed a steady increase after an initial remoulding stage in contractile soils (normally consolidated and lightly over-consolidated), but a steady reduction in the heavily over-consolidated, more dilatant, crust. The magnitude of pipe-soil stiffness changes (during both remoulding and reconsolidation) is governed by the over-consolidation ratio of the soil and the amplitude of the cyclic displacements. This study provides insights on the relevant cyclic stiffness to consider when assessing SCR fatigue life in over-consolidated soils and soils exhibiting a superficial crust layer.     

Assessment of fatigue strength of steel butt-welded joints in as-welded condition – Alternative approaches for curve fitting and mean stress effect analysis

Experimental fatigue data for butt-welded joints in as-welded condition and under constant amplitude tensile loading (secondary bending included) were analyzed using the nominal stress system and the notch stress system. Two approaches were used; a standard fitting procedure and minimization of the sum of squared perpendicular distances from a line with a fixed and free slope. In all cases, the latter method gave better agreement between the experimental and predicted fatigue life and fatigue strength. The analyses showed both with all broken specimen data included and with reduced data that the FAT225 curve, as recommended by IIW, might be too optimistic for the notch stress approach in the case of butt-welded joints in as-welded condition. It was also found that use of the local stress ratio instead of the applied stress ratio might explain many issues concerning current observations and apparent inconsistencies in reported literature.     

混凝土在路桥桩基施工中的作用及技术

路桥桩基混凝土施工中，为了保障灌注桩混凝土的质量，必须加强对准备工作及施工工艺的重视。通过对混凝土及其施工质量要求进行分析，探讨了混凝土在路桥桩基施工中的配合比、泵送等，并阐述了路桥桩基施工技术。     

国家助学贷款资产证券化制度设计研究

在2004年的国家助学贷款新政策背景下,尽管出现了许多利好方面,仍存在一些尚未解决的问题。而完整的国家助学贷款市场应当是由一级市场和二级市场组成的一个有序开放式的市场体系：一级市场是创造国家助学贷款形成借贷关系的市场,二级市场是创造国家助学贷款债权转让的市场。资产证券化是我国目前解决问题、完善市场、金融创新的重要选择,这项选择不仅很有必要,且基本具备了可行条件。当然,我国如果进行国家助学贷款资产证券化,还需要建立良好的征信制度和其它保障制度。