风积沙的工程力学性质试验研究

结合毛乌素沙漠沙样,对风积沙的工程力学性质进行了系统的试验研究。试验结果表明:风积沙的压实可采用常规的击实试验方法和振动密实法,压实效果受颗粒级配、含水量、荷载大小、振动频率及振幅等多种因素影响;风积沙的内摩擦角与压实度之间呈线性变化规律,颗粒级配是主要影响因素,含水量影响较小;风积沙的室内回弹模量和加州承载比与压实度之间大致呈非线性增大规律,在某一压实度区间增大的幅度非常小。     

考虑电动自行车骑行的非机动车道最大纵坡探讨

现行规范要求非机动车道的最大纵坡不超过3.5%,但要在山地城市、跨江桥梁两岸慢行系统衔接等场景下满足该要求存在工程占地大、造价高、可实施性差等问题,考虑到电动自行车在非机动车出行方式中占比越来越高的实际情况,以《电动自行车安全技术规范》（GB 17761—2018）规定的国标电动自行车为研究对象对骑行过程进行受力分析,提出了可满足电动自行车骑行要求的非机动车道最大纵坡参考值,可供电动车骑行占比高的类似项目参考。     

Instantaneous communication throughputs of vehicular ad hoc networks

Vehicular ad hoc networks (VANETs) formed by connected vehicles in a traffic stream could be applied to improve safety, mobility, and environmental impacts of a transportation system. In this paper, we present analytical models for the instantaneous communication throughputs of VANETs to measure the efficiency of information propagation under various traffic conditions at a time instant. In particular, we define broadcast and unicast communication throughputs by the wireless channel bandwith multiplied by the average probabilities that one vehicle is a successful receiver and sender in a VAENT, respectively. With a protocol communication model, we derive formulas to determine the probabilities for an equipped vehicle to be a successful broadcast receiver and a successful unicast receiver/sender, and obtain broadcast and unicast throughputs along discrete and continuous traffic streams. We further examine the impacts on communication throughputs of the transmission range and the interference range of dedicated short range communication devices as well as the market penetration rate of equipped vehicles and the percentage of senders. Finally, we investigate the influence of shock waves on communication throughputs.     

不同RAP掺量下就地热再生沥青混合料空隙率优选分析

依托福建省某高速路面预防性养护工程,采用最大理论密度线理论设计了再生沥青混合料级配,通过马歇尔试验研究了RAP料在86%、90%、94%掺量下再生沥青混合料空隙率的变化,并基于二次回归方程建立了不同RAP掺量与再生沥青混合料空隙率之间的回归方程,说明了不同RAP掺量与空隙率之间的变化趋势。研究结果表明:随着RAP料掺量增加,再生沥青混合料空隙率在逐渐降低;当再生沥青混合料空隙率控制在4%时,RAP料掺量约为89%。     

Using GPS-data to determine optimum electric vehicle ranges: A Michigan case study

Fuel-switching personal transportation from gasoline to electricity offers many advantages, including lower noise, zero local air pollution, and petroleum-independence. But alleviations of greenhouse gas (GHG) emissions are more nuanced, due to many factors, including the car’s battery range. We use GPS-based trip data to determine use type-specific, GHG-optimized ranges. The dataset comprises 412 cars and 384,869 individual trips in Ann Arbor, Michigan, USA. We use previously developed algorithms to determine driver types, such as using the car to commute or not. Calibrating an existing life cycle GHG model to a forecast, low-carbon grid for Ann Arbor, we find that the optimum range varies not only with the drive train architecture (plugin-hybrid versus battery-only) and charging technology (fast versus slow) but also with the driver type. Across the 108 scenarios we investigated, the range that yields lowest GHG varies from 65 km (55+ year old drivers, ultrafast charging, plugin-hybrid) to 158 km (16–34 year old drivers, overnight charging, battery-only). The optimum GHG reduction that electric cars offer – here conservatively measured versus gasoline-only hybrid cars – is fairly stable, between 29% (16–34 year old drivers, overnight charging, battery-only) and 46% (commuters, ultrafast charging, plugin-hybrid). The electrification of total distances is between 66% and 86%. However, if cars do not have the optimum range, these metrics drop substantially. We conclude that matching the range to drivers’ typical trip distances, charging technology, and drivetrain is a crucial pre-requisite for electric vehicles to achieve their highest potential to reduce GHG emissions in personal transportation.     

内河航道桥梁船撞时船体最大变形量研究

目前在桥梁船撞防护的专项设计或船撞力专题研究中,对船舶撞击力的研究和桥梁在船舶撞击作用下的响应关注较多,而对船体最大变形量的研究较少。基于ANSYSLS-DYNA软件,对4种不同载质量的内河代表船舶在3种航速、2种碰撞角度下撞击4种墩型的船撞工况进行数值模拟,提取船体最大变形量,并分析船体最大变形量与船舶载质量、撞击速度、桥墩类型及撞击角度的关联性,同时与经验公式做对比。研究结果表明,撞击速度及撞击角度是船体最大变形量的主要控制因素,桥墩类型与之关系不明显。     

增大泥泵最大球形通道的方案

增大泥泵最大球形通道可以提升疏浚工程连续性,减少堵泵的风险,提高疏浚施工效率。泥泵最大球形通道和泥泵效率是泥泵设计中的矛盾点。针对上述问题通过调研提出了两种增大泥泵最大球形通道方案,采用数值模拟方法计算了3种方案的泥泵内部流场。通过对数值模拟结果的统计分析,对比3种方案泥泵的性能。确定了增大泥泵最大球形通道叶轮设计方案,为后续泥泵改造提供基础。     

基于粒子群算法的水下多元线阵阵形有源校正方法

针对存在阵元位置误差的水下多元线阵,提出一种基于粒子群优化算法的远场有源阵形校正方法.该方法选用2个辅助源分时工作方式,利用无条件最大似然方位估计算法构建目标函数,并通过粒子群算法对阵元位置进行寻优.利用该方法对均匀线阵进行性能仿真实验.结果表明:该方法稳健性好、校正精度高,具有一定的应用前景.     

重载情况下船舶及主机加速问题分析

针对目前一些船舶在恶劣海况下遇到的加速问题,以及通过转速禁区时间过长的问题,从螺旋桨匹配和主机内部设计两方面进行原因分析。围绕转速禁区功率裕度,结合相关案例,从轻螺旋桨裕度、转速禁区及MAN主机输出扭矩能力等方面入手,提出改进措施。     

动力定位船舶全速度路径跟踪CB导引自适应闭环控制

针对仅使用槽道推进器提供横向推力的动力定位船舶路径跟踪控制问题,建立慢变环境干扰影响下的非线性船舶数学模型,设计带有自适应干扰补偿的反步控制算法来消除环境干扰的影响。引入平行目标接近(CB)导引算法为跟踪控制生成期望速度矢量信号,通过与所提出的自适应反步控制算法相结合,得到不受船舶驱动特性限制的全速度范围动力定位船舶导引跟踪控制算法,应用李雅普诺夫稳定性理论证明系统跟踪误差渐进收敛到零。仿真结果表明通过调整导引算法参数可以调节船舶跟踪过程表现,并可以得到较好的控制精度。