靶场试验指挥控制中心系统及其应用

针对靶场试验指挥控制中心的应用需求，介绍靶场试验指挥控制中心系统的功能、特点以及体系结构和组成，分析系统研制的关键技术，说明该系统的应用范围。目前，该指控中心系统已成功地应用于某大型武器系统靶场试验中，取得了较好效果。     

自行式沥青路面养护车工程配置的量化分析

基于提高作业效率、降低工程成本和实现合理的养护设备保有量的目的,根据道路病害的成因和长期实地观测的结论,分析了沥青混凝土路面病害数量与自然光候、铺筑质量、行车荷载、养护里程和道路通车年限的关系,并以此为基础,提出了自行式多功能沥青路面养护车工程配置的量化方法。     

Assessment of the volume of fluid method for free-surface wave flow

This study was concerned with the free-surface wave flow around a surface-piercing foil. The volume of fluid method implemented in a Navier–Stokes computational fluid dynamics code was employed. Three widely used discretization schemes for the volume of fluid method were assessed for a test case that involved general ship waves, spilling breaking waves in front of the leading edge, and bubbly free surfaces in separated regions. A single computational approach was selected for the comparison, and a grid-dependence study was carried out. The computational results were validated against existing experimental data, showing good agreement. The validation results suggest that all three discretization schemes perform well, but the best and most efficient results were obtained using the high-resolution interface capturing scheme.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

水基型沥青清洗剂的研究

采用表面活性剂复配技术,经基质材料的性能对比及正交试验分析,开发出能在常温下迅速除去金属表面沥青且环保的水基型清洗剂;进一步,论文探讨了清洗方式、浸泡温度、清洗剂浓度以及浸泡时间等因素对金属表面清洗效果的影响,证实了该清洗剂良好的净洗力,验证了研发的清洗剂作为道路工程界传统沥青清洗剂替代品的可行性.     

电磁永磁混合磁悬浮列车的磁铁结构优化设计

根据力学模型提出了增大混合磁铁磁轭高度以提高承载力的方法,从承载能力、可控性及永磁工作点3个角度展开对混合磁铁结构参数的优化分析。理论分析及仿真结果表明,适当增大永磁截面积在满足系统承载力要求的同时能提高磁铁可控性;合理选取永久磁铁的截面积和厚度参数能保证磁铁工作在最大能积点。     

Ni—P—SiC化学复合镀层中SiC均匀共析的最佳参数研究

研究了镀复条件及工艺配方对 N-P-SiC 化学复合镀层中 SiC 均匀共析的影响.结果表明,Nj-P 合金基体中 SiC 微粒子均匀共析的最佳条件是:温度87±1℃,搅拌速度600r/min·K,pH=4.8,SiC 平均粒径 D_p=3.5μm,SiC 的添加量8g/L,析出速度12～14μm/h.本文还测定了镀层的显微硬度及磨损量,并用扫描电镜观察了磨损前后的表面形貌和结构.     

Limit braking of a high-performance motorcycle

A mathematical-model-based study of the limit braking of a high-performance motorcycle and rider is described. Front and rear brakes are operable independently. A dry road and high friction are presumed, such that full braking of the front wheel would lead to an overturn or ‘stoppie’ in colloquial parlance. Effective braking needs to maintain some loading on the rear wheel. A planar but otherwise detailed system model is set up and braking strategies for front and rear are devised. Parameters of the braking control schemes are derived with the help of an optimisation process, minimising the final speed in braking from high speed over a fixed time interval. Simulation results are examined critically and the strategy is developed until efficient use of the friction available is made. The nature of optimal braking events is demonstrated. The influences of slipper-clutch torque setting and the rear-tyre target load chosen are shown.     

在冷镦机下模芯内成型螺栓倒角

通过改进模具结构,在冷镦机上成型螺栓倒角,替代机械加工,提高生产效率,降低生产成本。