State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Vehicle lift-off modelling and a new rollover detection criterion

The modelling and development of a general criterion for the prediction of rollover threshold is the main purpose of this work. Vehicle dynamics models after the wheels lift-off and when the vehicle moves on the two wheels are derived and the governing equations are used to develop the rollover threshold. These models include the properties of the suspension and steering systems. In order to study the stability of motion, the steady-state solutions of the equations of motion are carried out. Based on the stability analyses, a new relation is obtained for the rollover threshold in terms of measurable response parameters. The presented criterion predicts the best time for the prevention of the vehicle rollover by applying a correcting moment. It is shown that the introduced threshold of vehicle rollover is a proper state of vehicle motion that is best for stabilising the vehicle with a low energy requirement.     

Insights into vehicle trajectories at the handling limits: analysing open data from race car drivers

Race car drivers can offer insights into vehicle control during extreme manoeuvres; however, little data from race teams is publicly available for analysis. The Revs Program at Stanford has built a collection of vehicle dynamics data acquired from vintage race cars during live racing events with the intent of making this database publicly available for future analysis. This paper discusses the data acquisition, post-processing, and storage methods used to generate the database. An analysis of available data quantifies the repeatability of professional race car driver performance by examining the statistical dispersion of their driven paths. Certain map features, such as sections with high path curvature, consistently corresponded to local minima in path dispersion, quantifying the qualitative concept that drivers anchor their racing lines at specific locations around the track. A case study explores how two professional drivers employ distinct driving styles to achieve similar lap times, supporting the idea that driving at the limits allows a family of solutions in terms of paths and speed that can be adapted based on specific spatial, temporal, or other constraints and objectives.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

基于小波和粒子群算法的HEV行驶状况辨识方法研究

针对混合动力汽车(HEV)行驶状况(道路坡度和整车载荷)变化难以有效识别,导致驱动系统控制策略不能有效满足驾驶员意图问题,以混联式HEV为研究对象,提出了基于小波滤波和粒子群算法的HEV行驶状况辨识方法。首先建立了汽车行驶状况辨识模型,采用最小二乘法确立了优化目标函数,其次研究了基于小波滤波和粒子群算法的HEV行驶状况辨识原理,最后进行了行驶状况粒子群智能算法辨识试验。在采集实车数据的基础上,对实车数据进行小波滤波,并运用行驶状况辨识方法对道路坡度和整车载荷进行了辨识,并对辨识结果进行小波滤波,结果表明,试验工况下整车载荷辨识的相对误差绝对平均值为2.71%,道路坡度辨识的相对误差绝对平均值为3.85%,验证了所提出方法的有效性。     

轻型汽油车N_2O排放特性研究

选择1辆满足国Ⅴ排放标准的轻型汽油车作为试验样车,应用全流稀释排放测试系统在FTP75和US06测试循环下,对车辆在不同测试工况下的N_2O排放水平、车辆N_2O排放的影响因素以及N_2O排放随着车辆里程增加的劣化情况进行了研究。研究结果表明:FTP75循环下的N_2O排放结果高于US06循环,前者是后者的4倍左右;在冷起动阶段,由于催化剂没有达到正常的工作温度,车辆会产生较多的N_2O排放,且随着燃油硫含量的增加,车辆的N_2O排放呈现上升的趋势;随着车辆里程的不断增加,车辆的N_2O排放存在一定程度的劣化。     

基于GPS载波相位信号确定运动体姿态的关键技术

应用GPS载波相位信号确定运动体姿态,针对二维两天线系统情况,设计了姿态测量系统的硬件结构及算法流程框图,文章介绍了GPS姿态测量的关键技术：GPS姿态观测方程、整周模糊度的解算、误差的消除。从系统设计角度证明了技术的可行性。     

后轮对独立回转转向架与传统转向架曲线通过性能的对比研究

利用典型的线性稳态模型对传统转向架和新型转向架（后轮对独立回转转向架）的曲线导向能力进行了分析。建立了具有14个自由度的非线性车辆模型,对最佳的一系纵向刚度布置（前导轮对的纵向刚度较小,跟从轮对的刚度较大）的新型转向架和传统转向架车辆的曲线性能进行了仿真对比。仿真结果表明,新型转向架的曲线导向性能优于传统转向架。     

双车道公路危险路段评价指标与安全改善对策

选取相邻路段车速差△V、车速降低系数SRC和速度离差作为鉴别双车道公路危险路段的三个评价指标,从道路工程措施和交通安全设施两方面对事故多发路段进行安全改善对策研究。以内蒙古S203公路为例,利用评价指标进行危险路段判析,针对K465＋900急弯陡坡危险路段,通过线形改造以及设置交通标志标线、减速设施、避险车道和防护设施等一系列工程改造措施,进行安全改善综合方案设计。