确定焊接反变形的数值模拟及规律分析

焊接接头附近局部的加热及冷却使被焊结构产生残余应力及角变形.目前在船厂精度控制中,通常采用构件焊接后对某些部位进行火工校正的方法来控制残余角变形.文章提供了另外一种有效控制结构残余角变形的方法:对结构焊前施加弹性的反向变形.利用热弹塑性有限元法来模拟结构的焊接过程,并对不同板厚、不同热源的结构分别进行数值模拟,最终确定焊接结构的弹性反变形规律:焊接前施加弹性反变形的结构在焊接后角变形趋于零.     

妈港仓码公司场桥“油改电”(高架直流)设计与实施

介绍了深圳妈港仓码公司场桥"油改电"高架直流方案的设计和实施。在总体介绍的基础上,着重介绍了高架供电的主要结构型式及特点,并介绍了制作与安装所满足的规范。     

Fatigue design for plug/ring type gas welded joints of sts301l including welding residual stresses

This paper presents a fatigue design method for plug and ring type gas welded joints, which incorporates welding residual stress effects. A non-linear finite element analysis (FEA) was first performed to simulate the gas welding process. The numerically predicted residual stresses of the gas welds were then compared to experimental results measured using a hole drilling method. In order to evaluate the fatigue strength of the plug and ring type gas welded joints, a stress amplitude (σ _a ) _R taling the welding residual stress of the gas weld into account was introduced and is based on a modified Goodman equation incorporating the effect of the residual stress. Using the stress amplitude (σ _a ) _R , the ΔP-N _f relations obtained from fatigue tests for plug and ring type gas welded joints having various dimensions and shapes were systematically rearranged into (σ _a ) _R -N _f relations. It was found that the proposed stress amplitude (σ _a ) _R could provide a systematic and reasonable fatigue design criterion for the plug and ring type gas welded joints.     

Effect on friction of engine oil seal with engine oil viscosity

Low viscosity engine oil can improve a vehicle’s fuel economy by decreasing the friction between the engine components. Frictional torque varies with the velocity change due to different viscosity characteristics of SAE grade 5W-20, 5W-30 and 5W-40 engine oils. The viscosity for each of these grades was measured to outline the effect low viscosity engine oils have on engine friction, which may lead to improved fuel economy. Engine oil seal frictional torque increases with the shaft rotational speed for all three engine oil grades. A decrease in engine oil seal frictional torque was confirmed when low viscosity engine oil was used. Also, the leak-free performance of the engine oil with the seal satisfied the life limit durability test criteria. Thus, low viscosity engine oil may be used to improve fuel economy by decreasing the frictional loss of the engine oil seal while having no negative impact on performance due to leak-free functioning.     

成品油管道水击保护

长距离成品油管道在密闭输送过程中,出现非正常停泵、误关阀门及混油界面经过泵等均会引起水击现象发生。水击波沿管道传播,极易导致管道局部超压而造成管道破裂、损坏设备等,故水击保护成为成品油管道密闭输送关键性的工艺技术之一。金嘉湖成品油管道在全线水击保护控制方面采用了进出站压力调节系统、分输站分油流量调节系统、出站压力超高泄放系统、进站低压泄放保护系统、进出站压力超限停泵联锁保护系统来保证管道事故工况时的安全。     

一种光学界面检测仪在成品油管道上的应用

在成品油输送工艺中,需要对管道中输送的不同油品界面进行检测,以达到分离不同油品,减少混油量的目的。应用在成品油管道中的油品界面检测方法有密度法、荧光剂法、光学界面检测法、超声波界面检测法。介绍了一种基于光学原理的油品界面检测仪（FuelCheck）的检测原理、组成、安装及在国内兰成渝与西南成品油管道上的应用,该界面检测仪的成功应用,提高了混油界面的检测能力,有利于成品油输油管线安全、平稳、高效运行。     

基于灰色马尔可夫理论的油气管道腐蚀剩余寿命预测

以灰色理论的标准GM（1,1）模型和马尔可夫TPM理论为基础,提出了基于灰色马尔可夫理论的油气管道腐蚀剩余寿命预测方法。利用灰色马尔可夫理论预测腐蚀油气管道剩余寿命的步骤主要包括：最大允许腐蚀深度的确定,腐蚀速率的预测以及剩余寿命预测。并基于该方法,采用VB系统开发了实用软件,简便可靠。该方法可以在腐蚀速率波动比较大的情况下预测油气管道的剩余寿命,为油气管道腐蚀检测周期的确定提供了科学依据。     

郑州地铁盾构隧道下穿加油站的沉降分析

郑州地铁1号线03区间盾构施工需下穿一加油站,该加油站平行布置3个尺寸相同的埋地储油罐,总容积为150 m3,属一级加油站。3个储油罐与左线盾构隧道的竖向净距为7.0 m,水平净距为2.7 m,该加油站属Ⅰ级风险源。为保证盾构施工的安全,提出针对性的盾构掘进控制措施,采用ANSYS通用有限元软件对盾构施工下穿加油站引起的沉降进行数值模拟,计算得到的地表最大累计沉降和倾斜率均未达到监测报警值;因此,加油站在盾构施工时可以正常营业。为了保证盾构的安全推进,提出2盾构的推进间距距离、土舱压力、同步注浆压力等控制措施。盾构掘进过程中的地表和建(构)筑物的监测结果表明:地表和建(构)筑物的最大累计沉降和沉降速率均未达到监测报警值,盾构已经安全穿越加油站,文章提出的盾构掘进措施和研究方法可为类似工程提供参考。     

曲轴箱通风系统机油消耗试验与改进设计

对某型车用直列4缸柴油机开展了机油消耗、窜气和曲轴箱压力试验研究,试验结果表明该发动机在低负荷低转速工况下燃油消耗与机油消耗的比值(机燃比)不满足设计要求,随着转速和负荷的提高,总机油消耗量呈增加趋势,曲轴箱通风(PCV)系统所占总机油消耗比例较高,各工况点平均值约为10%。借助CFD仿真手段对原油气分离器及改进方案进行了对比分析,得知原结构油气分离效率较低,改进方案分离效率大幅提高。验证试验表明,3种对比工况下改进方案窜气特性和曲轴箱压力均满足设计要求,PCV系统机油消耗均大幅度下降,说明改进方案合理可行。     

铁路螺杆式空气压缩机油的研制

为适应铁路新型客运机车装用螺杆式空气压缩机的需要,研制螺杆式空气压缩机油。经室内配方筛选、室内理化性能综合评定、现场运用装车试验,确定出研制油以聚a 烯烃(PAO)为主、酯类油为辅的复合合成油为基础油,加入一定比例的抗氧剂、防锈防腐蚀剂、抗磨剂、破乳剂、抗泡剂等多种添加剂,并严格按照试验确定的工艺调配而成。经室内理化性能综合评定,研制油倾点低,氧化安定性能、抗泡性能、抗乳化性能、防锈防腐蚀性能优异。经1年现场运用试验,研制油具有更好的抗乳化性和空气释放性,具有相当的抗磨性、氧化安定性。