宿迁市运河文化桥现状老桥护栏提升改造设计及应用

随着经济和社会的发展,城市道路的快速化改造工程越来越多。由于新建道路设计时速及标准均有提高,既有现状老桥的防撞护栏等级已经不能满足新建城市快速路标准的要求,需要对现有老桥防撞护栏进行提升改造。以宿迁市迎宾大道二期快速化改造工程为例,介绍了现状运河文化桥老桥防撞护栏的提升改造设计方案,并采用屈服线分析和强度设计理论及非弹性分析方法进行了计算分析。在实际工程应用中,取得了良好的效果,以期为类似的现状老桥护栏提升改造项目提供借鉴。     

混凝土抗剪强度尺寸效应的细观数值模拟

混凝土的抗剪强度关系到混凝土结构的安全。采用随机骨料模型模拟混凝土的细观结构,利用有限元方法数值模拟混凝土试件的细观损伤断裂和抗剪强度,将所得数值结果与混凝土重力坝设计规范参考值比较,结果较为吻合,从而为混凝土力学性能的数值模拟开辟了新途径。同时研究表明混凝土试件的抗剪强度存在明显的尺寸效应。     

松花江大桥异形双壁钢围堰的构造与分析

介绍了松花江大桥35#墩异形双壁钢围堰的构造,并用ANSYS对其结构进行了分析,得出了该结构的应力和位移分布,依据分析结果,优化了原设计尺寸,对提高产品的强度、刚度及安全性能具有一定的指导意义。     

高速动车组砂箱连接螺栓的强度评估

文章通过有限元方法模拟仿真高速动车组砂箱及其与车辆的连接，并根据车辆运行工况得出螺栓的各种连接载荷．再根据VDI2230标准对连接螺栓进行强度评估，以验证设计的合理性和可靠性。     

Experimental and finite element analysis of fatigue strength for 300 mm2 copper power conductor

The fatigue strength of a 300 mm² stranded copper conductor was investigated experimentally and by finite element (FE) analysis. An analytical model was also developed and validated. Wires taken from the outer layer of the conductor were fatigue tested in tension–tension loading and compared with similar data for wires taken from a 95 mm² conductor. The wire cross section was deformed due to the compacting process that was applied during fabrication. When corrected for stress concentrations due to the deformation the data for the two sets of wire fell within the same scatter-band. Full scale testing was carried out in a specially designed rig with constant tensile load and reversed displacement controlled bending with a fixed curvature variation. The loading is a simulation of the loading of a power cable hanging from a floating vessel through a bellmouth. Conductors were tested in two states; dry and lubricated. A finite element model was established for the copper conductor. The model was formulated by a combination of elastic beam and beam-contact elements that included the effects of friction. The effect of local bending due to contact forces was included in the model. Two contact conditions were investigated; the point (trellis) contact between adjacent layers of wire and the inline contact within each layer and between the first layer (centre wire) and the second layer. The FE model was validated by a calibration test of a full scale conductor, and by sensitivity studies varying the size and the number of elements of the model. Fatigue analysis of the conductor was carried out, based on the S–N curve for individual wires. Taking into account the effects of friction and local bending, agreement was obtained between predicted and experimental fatigue strength of the conductor, for the FE model as well as the analytical model.     

基于ANSYSWorkbench的动车组水箱吊装结构强度分析

动车组车上吊装结构的设计是否合理将关系着动车组的安全运行，在对动车组车内水箱吊装结构模型合理简化的基础上，利用ANSYSWorkbench软件创建了其有限元模型，并依据标准EN12663，确定了其载荷工况，完成了对C型槽、滑块、联接螺栓的强度校核，其结果对水箱结构的设计及优化提供了参考．     

大型汽车滚装船横向挠曲强度全船有限元分析

大型汽车滚装船（PCTC）自身结构的特殊性和横向挠曲强度的关键性，对其进行横向挠曲强度全船有限元分析十分必要。以8000车大型汽车滚装船为研究对象，采用通用软件MSC／PATRAN建立有限元模型．按照ClassNK规范进行载荷的选取和施加，最终得到了横向挠曲强度全船有限元分析结果。对大型汽车滚装船挠曲强度的直接计算有一定的指导作用。     

奇异积分处理技术在低频声散射数值计算中的应用

针对散射声场的计算问题，将奇异积分处理技术应用于目标的低频声散射的数值计算、理论验模与仿真试验。若果表明，ka＜3时，新方法的仿真结果与解析值以及等价面元近似方法取得了较好的一致；而ka≥3时，新方法的仿真结耙要好于等价面元近似方法。     

先张法槽式张拉台座承力杆设计分析

本文介绍了先张法槽式张拉台座的力杆的设计分析。分别从承受的张拉力、结构稳定分析、强度验算、确定横向联系梁间距和纵向变形方面对工程实际进行验算。解决了梁板加宽后张拉力增加而张拉台座承力杆截面不需要增大的实际问题。     

某汽车滚装船甲板结构的有限元计算分析

由于滚装船对甲板强度具有较高要求,实际设计过程中需要对其进行认真计算和校核.文中结合一艘客改滚装船的改造设计,按照中国船级社有关规范利用有限元软件ANSYS校核了该滚装船的甲板结构强度.提供了3种甲板结构设计方案,并对3种方案分别进行计算、分析、对比.