大直径灌注桩桩侧摩阻力试验研究

根据苏州地区4根大直径桥梁钻孔灌注桩桩侧摩阻力试验结果,给出了该地区主要土层的侧摩阻力及其极限摩阻力建议值。试验表明:相当一部分桩侧土层未能达到极限状态,只有54 5%～78 4%范围内的土层达到极限值;桩底沉渣直接影响桩顶沉降及极限承载力;随着长径比的加大,桩侧摩阻力发挥效率降低。     

汽车ABS滑模变结构控制的分析与仿真

汽车防抱制动系统(ABS)是改善汽车主动安全性的重要装置.本文介绍了滑模变结构控制方法,针对汽车ABS的特点利用此方法设计了控制器,并在MATLAB/Simulink的环境下进行了仿真,给出了仿真结果和评价.     

填石路堤原位抗剪试验研究

在路堤原位抗剪试验基础上，获取路堤原位抗剪强度指标内摩擦角φ和黏聚力C，以推滑平衡分析法为理论基础，提出4点基本假设，经过现场试验数据计算分析，论证了假设成立和推滑平衡分析法应用于填石路堤的正确性。     

港口高压电缆卷筒滑环箱防凝露措施

凝露造成高压电缆卷筒滑环箱绝缘下降、箱体内元器件损坏,必须加以解决。分析凝露形成条件和造成高压电缆卷筒滑环箱故障的原因。提出温度控制法和湿度控制法两种措施。效果良好,可供参考。     

重载货车摩擦缓冲器阻抗特性的数值模拟

为预测摩擦缓冲器的实际工作状态,从几何特征和作用原理的角度,建立详细的MT-2型缓冲器理论模型。首先,通过对缓冲器内部各摩擦元件的运动学和静力学分析,推导出缓冲器在准静态下的阻抗特性;其次,引入附加摩擦系数量化各摩擦元件之间动静态摩擦过渡时的黏滞补偿,并模拟出缓冲器在动态下的阻抗特性;最后,利用C80型货车冲击试验数据对该缓冲器的理论模型进行验证。验证结果表明:总体上,数值模拟和现场试验下的缓冲器示功曲线基本吻合,说明模型的正确性;局部上数值模拟中缓冲器从加载Ⅰ阶段过渡至加载Ⅱ阶段的突变现象在冲击试验中表现的并不明显,还有待进一步完善。     

磁力摩擦式辅助驱动在TBM连续皮带机中的应用

长大隧道TBM(tunnel boring machine)施工大多采用连续皮带机出渣,当运输距离较大时通常需要在中间增设辅助驱动,以降低胶带最大张力,从而降低胶带强度。为了提高辅助驱动的工程适应性,研发了磁力摩擦式辅助驱动系统,具有驱动力大、无二次转载、胶带无二次冲击损伤、结构简单、故障点少、结构紧凑占用空间小、安装方便和配置灵活等特点。该成果可用于采用钢丝绳芯胶带的TBM连续皮带机、支洞皮带机以及其他需要辅助驱动的胶带输送机,并在山西省中部引黄工程TBM1标段成功应用,具有广阔的推广应用价值。     

基于地基回弹因素的盾构隧道管片上浮预测

针对软弱地层盾构隧道管片脱出盾尾后出现的上浮问题,分析盾构施工过程中管片上浮的诱因,得出软弱地层中管片的上浮主要是地层应力重分布产生的地基回弹力引起的。在此基础上建立隧道开挖动态模型,分析隧道上浮量变化规律以及地层特性对管片上浮量的影响规律,得出地层弹性模量和管片上浮量呈一定的指数关系,且弹性模量对管片上浮量的影响远大于地层黏聚力和内摩擦角。通过力平衡理论计算盾构开挖引起的地层回弹力、管片上浮量以及隧道上浮影响的地层高度范围,并通过对珠江狮子洋工程管片上浮量的计算与实测对比,证明该公式的合理性,为盾构隧道工程中考虑地基抗力引起的管片上浮量预测提供一种新的方法。     

A receding horizon sliding control approach for electric powertrains with backlash and flexible half-shafts

Active control of electric powertrains is challenging, due to the fact that backlash and structural flexibility in transmission components can cause severe performance degradation or even instability of the control system. Furthermore, high impact forces in transmissions reduce driving comfort and possibly lead to damage of the mechanical elements in contact. In this paper, a nonlinear electric powertrain is modelled as a piecewise affine (PWA) system. The novel receding horizon sliding control (RHSC) idea is extended to constrained PWA systems and utilised to systematically address the active control problem for electric powertrains. Simulations are conducted in Matlab/Simulink in conjunction with the high fidelity Carsim software. RHSC shows superior jerk suppression and target wheel speed tracking performance as well as reduced computational cost over classical model predictive control (MPC). This indicates the newly proposed RHSC is an effective method to address the active control problem for electric powertrains.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

预应力锚索抗滑桩结构在处治滑坡中的应用

文章结合鹰阳关-莲塘二级公路K54+800处滑坡采用预应力锚索结构施工实践,介绍了预应力锚索抗滑桩结构在滑坡处治中的注意事项及使用效果.