多孔材料垂直渗透系数测定装置的研究

在对渗透系数影响因素的分析研究基础上,针对原有渗透仪在侧漏、低水头下测量困难等缺点,就测压管位置、测压管直径、测量用水及试件尺寸方面规范化多孔渗透系数测定仪。为减少试件表面附着的气泡,采用抽真空后,而不采用分层浸泡的方法。最后就渗透测定仪装置提出几条改进建议:用充气气囊代替柔性侧壁,用差压计代替微压计。实践证明本仪器使用稳定,数据重复性高。     

使用乙醇还原剂的NOx-SCR催化剂的性能评价

采用计算机辅助分析的方法设计了乙醇还原剂添加装置，并使用这套装置在发动机台架上进行了稀燃NOx选择催化还原（SCR）催化剂的性能评价试验。试验结果表明，在30000h^-1空速、排温为350～420℃范围的条件下，该催化剂的NOx转化率维持在90％以上，而在低温和高温下的转化率较低；随着乙醇添加量的增加，催化剂NOx转化率提高，但同时会增加THC排放；当空速超过40000h^-1后，催化剂性能有所下降。     

高速铁路路基边坡纤维团粒喷播生态防护技术

针对高速铁路路基绿化工程高要求、少维护等特点,提出纤维团粒喷播技术,并详细阐述了其机理及特点.通过在京雄城际铁路路基边坡工程中的应用,归纳总结了该技术施工工艺流程:平整坡面→坡面覆土→铺设铁丝网→喷播基质→养护管理.喷播基质是利用喷播机械将性能优越的基质材料喷附至铁路路基坡面上的.工程应用表明该技术施工快,质量好,养护维修量小,经济性高.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

Tuning of transfer functions for analysis of wave–ship interactions

Transfer functions are often used together with a wave spectrum for analysis of wave–ship interactions, where one application addresses the prediction of wave-induced motions or other types of global responses. This paper presents a simple and practical method which can be used to tune the transfer function of such responses to facilitate improved prediction capability. The input to the method consists of a measured response, i.e. time series sequences from a given sensor, the 2D wave spectrum characterising the seaway in which the measurements are taken, and an initial estimate of the transfer function for the response in study. The paper presents results obtained using data from an in-service container ship. The 2D wave spectra are taken from the ERA5 database, while the transfer function is computed by a simple closed-form expression. The paper shows that the application of the tuned transfer function leads to predictions which are significantly improved compared to using the transfer function without tuning.     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.     

Optimal bus fleet management strategy for emissions reduction

Transportation is a major cause for environmental degradation via exhaust emissions. For many transit-oriented metropolitan areas, bus trips often constitute a sizeable mode share. Managing the bus fleet, in particular updating buses to comply with the newer emissions standards, therefore, can have a substantial impact on transportation-induced air quality. This paper presents the approach of remaining life additional benefit–cost (RLABC) analysis for maximising the total net benefit by either early-retiring or retrofitting the current bus fleet within their lifespans. By referring to the net benefits for different bus types estimated by RLABC analysis, the most beneficial management scheme for the current bus fleet can be identified. Optimal bus fleet management (BFM) models based on the RLABC analysis for the operator and the government are developed. Then a government subsidy plan is produced to achieve win–win solutions, which will offer efficient and flexible management schemes. To illustrate the approach, the largest bus company in Hong Kong, which carries more than 23% of the total trips in Hong Kong, is taken as a case study example. Instead of adopting a fixed retirement plan, such as replacing buses at the age of 17 as is currently practised, the proposed method develops an optimal BFM scheme that progressively phases out buses or retrofits them. This study produces promising results to demonstrate the large benefit of this approach for optimal bus fleet management.