挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

超深振捣条件下混凝土墙体模板侧压力的简化计算方法

超深振捣对混凝土成品质量有害无益,研究超深振捣引起模板侧压力增大的规律,可为规避其害提供依据。为此设计4个混凝土墙体试件,实测在浇筑过程中模板侧压力的变化情况。基于振捣液化和液体压力平衡理论,建立了超深振捣情况下混凝土模板侧压力计算模型,推导了计算公式,并与实验数据进行对比验证。研究结果表明,振捣深度是影响混凝土墙体模板侧压力的重要因素,本文提出的计算模型能很好地预测墙体结构超深振捣位置的模板侧压力。     

A regression and beam theory based approach for fatigue assessment of containership structures including bending and torsion contributions

Container shipping has been expanding dramatically during the last decade. Due to their special structural characteristics, such as the wide breadth and large hatch openings, horizontal bending and torsion play an important role to the fatigue safety of containerships. In this study the fatigue contributions from vertical bending, horizontal bending and torsion are investigated using full-scale measurements of strain records on two containerships. Further, these contributions are compared to results from direct calculations where a nonlinear 3D panel method is used to compute wave loads in time domain. It is concluded that both bending and torsion have significant impacts on the fatigue assessment of containerships. The stresses caused by these loads could be correctly computed by full-ship finite element analysis. However, this requires large computational effort, since for fatigue assessment purposes the FE analysis needs to be carried out for all encountered sea states and operational conditions with sufficient time steps for each condition. In this paper, a new procedure is proposed to run the structure finite element analysis under only one sea condition for only a few time steps. Then, these results are used to obtain a relationship between wave loads and structural stresses through a linear regression analysis. This relation can be further used to compute stresses for arbitrary sea states and operational conditions using the computed wave loads (bending and torsion moments) as input. Based on this proposed method for structure stress analysis, an efficient procedure is formulated and found to be in very good agreement with the full-ship finite element analysis. In addition it is several orders of magnitude more time efficient for fatigue assessment of containership structures.     

西南红层软岩地区铁路滑坡形成机理分析及治理措施

红层软岩地区铁路工程建设中滑坡问题突出。本文结合西南地区一铁路红层滑坡治理工程,利用该地区红层滑坡的现场调查结果,从红层软岩特性、地层岩性、地质地貌、水文地质条件、深孔位移监测数据等多方面对该地区铁路滑坡形成机理进行分析,并论述红层滑坡与一般滑坡的不同点,分析红层软岩岩体力学特性、地层主要成分以及红层软岩中的粉砂质泥岩在不同风化程度下的力学特性。根据分析结果提出治理措施,并对治理措施进行评价。总结得出地层岩性、地质水文、人为因素是导致红层滑坡病害发生的主要因素。     

Catenary riser sliding and rolling on seabed during induced lateral movement

Catenary risers have an interaction zone with the seabed, usually referenced as flowline. Movements in this region can be induced by sea currents and large offsets in floating unit, leading to touchdown position changes and affecting internal loads along riser length. In this work the contact flowline-seabed is modeled including sliding and rolling friction. Case studies involving large offsets in floating unit and lateral sea currents are solved to better understand the consequences of possible rolling and large sliding. The riser is modeled using a geometrically-exact finite element beam model. The contact is addressed with a new technique to include rotation movements from underlying beam models. This leads to global riser models including complex kinematics, being able to represent scenarios with alternating sliding/rolling and its consequences on internal loads of riser structure. A parametric study is performed to measure the influence of the friction coefficient in tension and torsion along typical flexible pipe and steel pipe catenary risers.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

桥墩及桩基形式对墩底平转施工转盘设计的影响

以新建福厦(福州—厦门)高速铁路17500 t转体刚构为背景,采用实体有限元方法分析了不同桥墩类型及桩基布置对墩底平转转体中转盘受力的影响,并对桥墩及桩基进行了优化。结果表明:实体墩对上转盘受力最有利,其次是空心墩,最不利的是双薄壁墩;增加墩底实体段能够有效降低空心墩、双薄壁墩上转盘的主拉应力;随着墩底实体段高度的增加,主拉应力降低的幅度逐渐变小;球铰正下方有桩基时对下转盘底部受力更加有利;距离球铰中心越远,桩基受力越小,适当增加中桩桩径,可使各桩基应力状态更加均衡。     

车辆隔热壁K值计算中空气层的处理方法

对轨道交通车辆多层复合结构的隔热壁进行隔热性能理论计算与仿真计算的对比,对隔热壁内部空气层的隔热性能进行分析。结论为:在车辆多层复合结构的隔热壁K值计算中,当空气层厚度大于一定厚度时,流体自然对流对隔热壁的隔热性能影响较大。利用多项式密度(Polynomial Denisity)和Boussinesq模型两种算法,对所得结论进行了验证。     

格拉斯磁环匀强磁场分析

以毕奥-萨伐尔定律为基础,建立亥姆霍兹线圈以及格拉斯磁环中心磁场分布模型,并计算了它们内部的轴向磁感应强度分布,绘出了空间分布图,分析了轴向磁感应强度与x、y坐标的关系,分析结果得到了亥姆霍兹线圈和格拉斯磁环内部匀强磁场分布区域,通过比较得到格拉斯磁环内部的匀强磁场区域比亥姆霍兹线圈内部的匀强磁场分布区域更大的结论。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.