多孔材料垂直渗透系数测定装置的研究

在对渗透系数影响因素的分析研究基础上,针对原有渗透仪在侧漏、低水头下测量困难等缺点,就测压管位置、测压管直径、测量用水及试件尺寸方面规范化多孔渗透系数测定仪。为减少试件表面附着的气泡,采用抽真空后,而不采用分层浸泡的方法。最后就渗透测定仪装置提出几条改进建议:用充气气囊代替柔性侧壁,用差压计代替微压计。实践证明本仪器使用稳定,数据重复性高。     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

水泥混凝土路面质量病害问题探讨

根据目前水泥混凝土路面建设比较普遍的情况,针对施工中出现比较多的质量病害进行了分析,分别从水泥混凝土路面的裂缝产生的过程,材料、配合比、水灰比、施工操作等对质量的影响,以及产生外观质量缺陷的原因进行了评述.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

Tuning of transfer functions for analysis of wave–ship interactions

Transfer functions are often used together with a wave spectrum for analysis of wave–ship interactions, where one application addresses the prediction of wave-induced motions or other types of global responses. This paper presents a simple and practical method which can be used to tune the transfer function of such responses to facilitate improved prediction capability. The input to the method consists of a measured response, i.e. time series sequences from a given sensor, the 2D wave spectrum characterising the seaway in which the measurements are taken, and an initial estimate of the transfer function for the response in study. The paper presents results obtained using data from an in-service container ship. The 2D wave spectra are taken from the ERA5 database, while the transfer function is computed by a simple closed-form expression. The paper shows that the application of the tuned transfer function leads to predictions which are significantly improved compared to using the transfer function without tuning.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.