轨道交通信号控制系统LCC估算方法研究与应用

从产品全生命周期成本概念出发,阐述了轨道交通信号控制系统生命周期的特点和成本构成;从企业视角提出了一种轨道交通信号控制系统的LCC估算方法;通过企业项目成本管理信息化系统统计产晶LCC的各项数据,结合财务数据进行归一化估算,并定期进行回归迭代,规范化实施分析与评价,从而得出产話的LCC改进建议,为公司战略决策提供了重要参考依据。     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

基于Matlab油船意外泄油性能的程序设计

基于概率方法的意外泄油性能参数计算是2010年1月1日及以后新造船破舱稳性需要评估的性能之一,满足一定的衡准要求方可。根据油船的分舱分别进行船底破损概率和船侧破损概率的插值,然后按照一定的公式求出船底破损后与船侧破损后的泄油量的加权之和,即意外泄油性能参数。由于手工计算费时费力,文章基于Matlab平台,开发了意外泄油性能参数的自动计算程序模块。计算结果与文献结果相比较,证明了本程序的计算精度,具有较好的工程实用价值。     

Analysis of cross effect on inherent deformation during the line heating process – Part 1 – Single crossed heating lines

This paper describes the effect of previous heating on inherent deformation by a subsequent heating line, more specifically, the case of two heating lines intersecting (crossing) each other. The paper has been divided into two parts. In the first part, the case of single crossed heating lines is studied in detail. The second part of the paper, discusses the case of more than one crossed heating lines. The novelty of the work lies in revealing the cross effect and how, factors such as, for example, the heating condition and the plate geometry, influence the resulting inherent deformation of crossed heating. In addition, relationships to easily get these influences are provided. The results are suitable for a wide range of heating conditions and plate thickness.     

基于改进型消灭曲线法的横摇阻尼估算

自由衰减试验仍是目前最为有效且常用的估算横摇阻尼系数的方法.横摇阻尼系数的估算精度对于船舶横摇运动的预报起着至关重要的作用.通常采用所谓的消灭曲线法来分析自由横摇衰减数据.该方法的一个不足之处在于其推导是基于忽略了非线性恢复力项的自由横摇运动方程.另一方面,考虑更多非线性成分的能量法能够纳入该因素影响但在实施过程中较为复杂.文中提出了一种改进型的消灭曲线法,能够纳入船体非线性恢复力项的影响.所提出的方法形式简单且相比能量法更易于实施.数值试验证明了改进型消灭曲线法的正确性,并展现了其相对传统消灭曲线法所具有的优势.     

Full six degrees of freedom coupled dynamic simulation of ship collision and grounding accidents

By taking advantage of the user-defined load subroutine (loadud) and the user common subroutine (usercomm) in LS-DYNA, the authors proposed a new coupled approach for simultaneously calculating structural damage and the planar 3DOF ship motions in ship collisions. The coupled procedure aimed at predicting the detailed structural damage together with reasonable global ship motions. This paper extends the method to consider the full 6DOF ship motions; thus, ship collision as well as grounding accidents can be properly handled. This method is particularly useful for design purposes because the detailed ship hull profile is not needed.A traditional ship maneuvering model is used for the in-plane surge, sway and yaw degrees of freedom with a series of nondimensional coefficients determined from experiments. It is assumed that the out-of-plane degrees of freedom are not coupled with the in-plane ship motions, and there is no coupling among roll, pitch and heave motions. The implementation is verified through free decay tests, and the obtained natural periods show good agreement with theoretical results.Several collision and grounding cases are simulated in which a supply vessel crashes into rigid plates with different orientations. The effects of the roll motion, the heave and pitch motions and the full 6DOF motions are studied. The results are compared with those from a 6DOF decoupled method. Ship motions through the proposed method compare reasonably well with SIMO results. It is found that several consecutive impacts may occur in the simulation of one collision case due to the periodic motions. This is not taken into account in the decoupled method, which makes this method unconservative.     

Hydroelastic analysis of oblique irregular waves with a pontoon-type VLFS edged with dual inclined perforated plates

The fluid-structure interaction of oblique irregular waves with a pontoon-type very large floating structure (VLFS) edged with dual horizontal/inclined perforated plates has been investigated in the context of the direct time domain modal expansion theory. For the hydroelastic analysis, the boundary element method (BEM) based on time domain Kelvin sources is implemented to establish water wave model including the viscous effect of the perforated plates through the Darcy’s law, and the finite element method (FEM) is adopted for solving the deflections of the VLFS modeled as an equivalent Mindlin thick plate. In order to enhance the computing efficiency, the interpolation-tabulation scheme is applied to assess rapidly and accurately the free-surface Green function and its partial derivatives in finite water depth, and the boundary integral equation of a half or quarter VLFS model is further established taking advantage of symmetry of flow field and structure. Also, the numerical solutions are validated against a series of experimental tests. In the comparison, the empirical relationship between the actual porosity and porous parameter is successfully applied. Numerical solutions and model tests are executed to determine the hydroelastic response characteristics of VLFS with an attached anti-motion device. This study examines the effects of porosity, submerged depth, inclined angle and gap distance of such dual perforated anti-motion plates on the hydroelastic response to provide information regarding the optimal design. The effects of oblique wave angle on the performance of anti-motion and hydroelastic behavior of VLFS are also emphatically examined.     

横梁端部节点优化

通过有限元计算,对比几种常见的横梁端部连接方式,综合考虑结构整体强度、钢材使用量、舱室空间利用率、施工便利性等方面的影响因素,确定较优的连接过渡方式和过渡结构的参数尺寸,为船舶设计横梁端部节点形式的确定提供参考。