超大型浮式生产储油轮货油舱脚手架设计新思路

脚手架是造船及建筑等行业必须应用的辅助工具之一.设计快速搭建和方便拆卸,且满足有关国际安全标准和行业安全规范的脚手架,是我国造船业缩短建造周期、降低建造成本的一项紧迫任务.文章以上海外高桥造船有限公司承接的渤海二期油田30万吨FPSO货油舱脚手架结构设计为例,设计了一种符合国际安全标准、快速搭建和方便拆卸的脚手架结构形式.     

长撑杆双颚板绳索抓斗自重的确定及其在抓斗各部件上的分配比例

主要阐述抓斗的主要参数之一——抓斗自重及其在抓斗各部件上的分配比例对抓斗性能的影响;抓斗抓取量与抓斗自重、散货物理-力学性质之间的关系,提出了如何合理确定抓斗自重及其在抓斗部件上的分配比例的方法。     

广州港南沙港区二期工程平面布置要点

通过总结广州港南沙港区二期工程平面布置,提出集装箱码头平面布置的设计要点,为类似工程提供参考.     

快速测定铝／氧化银电池电解液中碱浓度的方法

用传统化学分析方法测量铝／氧化银电池电解质溶液组分浓度耗时长。针对这一弊端,本文提出通过测量电解质溶液密度、温度,然后结合计算出的铝酸盐浓度,再对照在不同温度下电解质溶液密度与铝酸盐浓度关系曲线图,快速确定电解质溶液中碱的浓度的方法。在电池实际放电过程中证明该方法行之有效。     

浅埋暗挖隧道下穿结构物的施工沉降分析

以北京地铁奥运支线起点(熊猫环岛站)区间隧道下穿健安桥的设计与施工为背景,分析浅埋暗挖隧道穿越地面结构物施工如何有效地控制沉降,探讨施工时应注意的关键环节和采取的措施,以此作为今后类似工程施工的依据和借鉴.     

公路水泥混凝土路面基层顶面当量回弹模量非线性计算公式归一化的研究

鉴于1994年和2002年水泥混凝土路面设计规范中,基层顶面当量回弹模量确定过程存在的繁琐性,有必要通过回归分析,对2002年规范所提供的六个计算公式加以简化。实践表明,该简化能够满足计算要求并取得满意的效果。     

摩托车规费稽查方式探讨

针对摩托车规费依靠稽查征收的原因分析入手．指出了传统稽查方式中存在的缺点, 提出了应采取的正确措施。     

改性沥青设备在作业中常见的故障及应对措施

采用合理的工艺流程,注意防止和处理设备在运行中出现的各种问题及故障,并在使用中积累必要的经验,是保证改性沥青（成套）设备安全生产及保证产品质量的关键之一。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Characteristics and Development Trends of the Support Technology of High Ground Stress Tunnels in China北大核心CSCD

Combining the present situation and development trend of different tunnel support technologies at home and abroad, this paper analyzes the problems of rockburst in hard rock tunnels and large deformation in soft rock tunnels caused by high ground stress. It is concluded that: 1) regarding the rockburst problem, the current support technology is mainly influenced by the rock burst mechanism which is dominated by static factors, and so the used support components are generally of smaller deformation performance and "passive support" properties; 2) as the rockburst is the result of dynamic-static stress coupling, and only the anchor bolt has the "active support" attribute in the current "shotcrete+anchor bolt+wire net" support system, so the best support system should have the two functions of active support and energy release in terms of the rockburst problem, and the key focus of the research and development is anchorage members; 3) there are three main support types for large deformation in soft rock tunnels, e.g. the heavy support, layered support and yielding support. Among them, the heavy support system in underground cavern with large deformation is easy to induce excessive surrounding rock pressure, and so the applicable conditions are limited. The layered support system is still not the best choice due to its immature theoretical study, difficult determination of the thickness value and the installation time of each support layer and the interference to construction progress. With the characteristics of timely support and yielding while supporting, the yielding support system can give full play to the performance values of surrounding rocks and supporting materials, and make both of them reach the optimal state, so it is the best choice for supporting the soft rock tunnels with large deformations. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.