鲁家峙钢管混凝土拱桥混凝土系杆梁施工中的关键技术

鲁家峙钢管混凝土拱桥混凝土系杆梁采用支架现浇混凝土施工方法,介绍了高支架模的设计、施工,系杆梁的线形控制措施及下锚箱位置控制措施。     

沉管隧道地震响应分析

文章采用田村重四郎和冈本舜三提出的沉埋隧道地震响应分析的数学模型,对南京长江越江隧道(沉管段)方案进行了地震响应的纵向受力分析。分析中采用了隧址处100年超越概率为2%的人工合成地震加速度,考虑了不同管段的联结方式和不同的计算参数,对初步设计中沉管段结构的安全性进行了论证,所提供的数据曾为设计单位所采纳[1]。     

整体式无接触热阻散热器传热元件的研究

介绍了国内首次研制成功的Al质整体式无接触热阻散热器翅片管传热元件的结构与特点 ,对整体式无接触热阻散热器与管带式散热器进行了对比试验 ,并对试验所得的传热与阻力进行了分析。试验结果表明 ,无接触热阻散热器传热性能和可靠性优于管带式散热器 ,且体积小 ,质量轻 ,工序少 ,是目前车用管带式散热器理想的替代产品     

车用液力变矩器的变形仿真研究

为确保液力变矩器的使用安全，对液力变矩器（空壳）在同一离心力场下的不同油压作用进行了实际工况仿真和有限元分析，通过对实际车用液力变矩器空壳的试验测试，结果表明液力变矩器颈端（Hub)和柄端（Pilot)的轴向变形与油压呈线性关系，理论计算值与试验测试结果吻合较好。     

液力变矩器焊接的数值模拟和质量控制

对液力变矩器的制造精和质量要求很高，焊后必须保证产品的尺寸精度，并要进行疲 试验以考虑焊缝的强度。通过分析计算，可以预测各种条件对焊接变形的影响；发现疲劳承载时的最危险断面在不在焊缝处，而是在上盖板的弯角处。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

大跨度钢管桁架无柱雨棚施工技术

重庆江北火车站大跨度钢管桁架无柱式雨棚,高14m,长540m,建筑面积达56230m2。结构工程跨度大,场地条件复杂,施工制约因素多,质量要求高。对主桁架等大型构件首次采用加工厂下料、现场加工制作、现场拼装、整体吊装的方案。详述了主桁架的吊装、焊接等工艺和施工控制措施。通过合理选择施工方案,严格按照工艺要求,合理安排施工程序,保证了工程如期保质保量的完成。     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

真空管道运输系统管道模型结构分析与实验内容

对真空管道运输(ETT)系统管道实验模型的整体结构和尺寸、主要功能部件的设置以及该管道实验模型建成后将进行的实验内容等进行了分析和介绍。