公路隧道LED照明模拟控制系统设计

为更有效地设计隧道照明,针对隧道LED照明模拟设计欠缺的现状,基于Zigbee无线通信研发了隧道LED照明模拟控制系统,提出并设计了车载照度采集装置,实现对隧道内亮度的连续检测。实验分析表明:车载照度采集装置误差在-5.69%~3.06%之间,隧道模型设计亮度误差在-4.49%~5.57%之间,具有较高的可靠性。最后,研究成果已应用到隧道照明改造的模拟设计中,改造后节能百分比达53.6%。     

缓倾顺层岩质边坡变形数值模拟及处治方案研究

以黄花互通D匝道边坡为依托,采用FLAC软件对边坡进行数值模拟,探讨了水力作用对边坡变形破坏的影响;分析了预应力锚杆边坡加固前后模型水平位移变化。研究表明,加固后边坡稳定性大为改善,在水力作用下,边坡各处位移也非常小,甚至小于加固后无水力作用的情况。通过现场边坡位移监控,评价了该边坡处治效果。     

软弱围岩隧道管棚水平旋喷组合预加固变形规律

为研究软弱围岩地层管棚水平旋喷桩组合结构的预加固效果,采用三维弹塑性有限元方法对比分析了单独使用管棚、单独使用旋喷桩、管棚与旋喷桩组合预加固及无加固4种工况下隧道结构体系的位移变化规律。结果表明:1)水平旋喷桩和管棚2种工法中,水平旋喷桩预加固工法控制拱顶下沉、拱脚收敛值和掌子面稳定性能力显著;2)管棚预加固工法控制地表沉降的能力较强;3)管棚和旋喷桩组合结构控制拱顶沉降和拱脚收敛,掌子面水平位移性能突出,管棚水平旋喷桩组合结构使地表沉降减小91.3%,拱顶沉降减小76.2%,拱脚收敛减小76.3%,其地表最大沉降值为2.7 mm,拱顶最大沉降值为25 mm,拱脚最大收敛值为4mm,最小收敛值为-9.4 mm,加固效果明显。     

郑州地铁盾构隧道下穿加油站的沉降分析

郑州地铁1号线03区间盾构施工需下穿一加油站,该加油站平行布置3个尺寸相同的埋地储油罐,总容积为150 m3,属一级加油站。3个储油罐与左线盾构隧道的竖向净距为7.0 m,水平净距为2.7 m,该加油站属Ⅰ级风险源。为保证盾构施工的安全,提出针对性的盾构掘进控制措施,采用ANSYS通用有限元软件对盾构施工下穿加油站引起的沉降进行数值模拟,计算得到的地表最大累计沉降和倾斜率均未达到监测报警值;因此,加油站在盾构施工时可以正常营业。为了保证盾构的安全推进,提出2盾构的推进间距距离、土舱压力、同步注浆压力等控制措施。盾构掘进过程中的地表和建(构)筑物的监测结果表明:地表和建(构)筑物的最大累计沉降和沉降速率均未达到监测报警值,盾构已经安全穿越加油站,文章提出的盾构掘进措施和研究方法可为类似工程提供参考。     

基于有效绿灯时间利用率的自适应控制策略研究

为了优化单点交叉口信号控制方案,使其适应各个进口道方向交通流动态变化,提高交叉口通行效率,根据交叉口进口道排队车辆数建立有效绿灯利用率模型,提出了一种交叉口自适应控制策略.有效绿灯时间利用率模型以交叉口通行能力最大为控制参数,实时优化确定出最佳相位放行方案以及最优相位切换方案,根据进口道排队车辆最大流向的排队车辆数和车辆到达预测确定相位放行绿灯时间.利用VISSIM交通仿真软件对该自适应控制策略仿真运行,与定时控制以及感应控制对比,评价分析不同车辆到达情况下交叉口通行情况.结果表明:该自适应控制策略能有效降低车均延误,提高交叉口服务水平.     

Perspectives on railway track geometry condition monitoring from in-service railway vehicles

This paper presents a view of the current state of monitoring track geometry condition from in-service vehicles. It considers technology used to provide condition monitoring; some issues of processing and the determination of location; how things have evolved over the past decade; and what is being, or could/should be done in future research. Monitoring railway track geometry from an in-service vehicle is an attractive proposition that has become a reality in the past decade. However, this is only the beginning. Seeing the same track over and over again provides an opportunity for observing track geometry degradation that can potentially be used to inform maintenance decisions. Furthermore, it is possible to extend the use of track condition information to identify if maintenance is effective, and to monitor the degradation of individual faults such as dipped joints. There are full unattended track geometry measurement systems running on in-service vehicles in the UK and elsewhere around the world, feeding their geometry measurements into large databases. These data can be retrieved, but little is currently done with the data other than the generation of reports of track geometry that exceeds predefined thresholds. There are examples of simpler systems that measure some track geometry parameters more or less directly and accurately, but forego parameters such as gauge. Additionally, there are experimental systems that use mathematics and models to infer track geometry using data from sensors placed on an in-service vehicle. Finally, there are systems that do not claim to measure track geometry, but monitor some other quantity such as ride quality or bogie acceleration to infer poor track geometry without explicitly measuring it.     

<TPL-PCRUN> Statement of methods

TPL-PCRUN is a software program for the dynamic interaction simulation of pantograph–catenary systems. In the benchmark, based on the finite element method, the catenary model was built and the pantograph was considered as a three-level spring–damper–mass system. Then, through the contact definition between pantograph and catenary, the coupled model of the pantograph and catenary system was established. The respective dynamic equations of motions were solved by the time integration method. Thus, the simulation results were obtained and submitted for the comparison with the other software. On the other hand, a standard model from EN50318 was established and analysed by TPL-PCRUN. The simulation results by TPL-PCRUN were remarkably consistent with the reference values given by EN50318. It was proved that the results by TPL-PCRUN can be reliable. Recently, the software has been updated and improved. Some new models and algorithms are proposed, including the rigid–flexible hybrid pantograph model, contact definition considering appearance characteristics of the contact surfaces, a fluid–solid coupling algorithm of the pantograph and catenary system, etc.     

连接片阻值对电动汽车用动力电池性能的影响

鉴于单体电池间连接片的阻值和极柱的位置影响单节电池的性能,基于Matlab/Simscape开发了单体电池模型,并利用此模型和以电阻模拟的连接片构建了单节电池模型,仿真分析了连接片阻值对单节电池性能的影响。结果表明,连接片的存在使与极柱相连的单体电池最先达到电池管理系统设定的放电截止电压,以致影响电池的性能;与极柱相连的单体电池的率先老化导致与其相邻的单体电池出现过放电的现象,影响单节电池的安全性。最后,设定各单体电池SOC间最大偏差为0.05,对不同并联电池数目的单节电池进行仿真,得出连接片与电池欧姆内阻阻值的合理比例。     

钱江隧道火灾疏散可靠性分析

为评估钱江隧道火灾疏散的可靠性,从而为钱江隧道逃生通道设置方案决策提供参考依据,基于改进的公路隧道需用安全疏散时间RSET计算法,采用Monte Carlo随机数值试验方法,针对钱江隧道的特点,对3种不同的逃生通道方案进行公路隧道火灾人群疏散随机性仿真模拟,从而可计算不同疏散逃生方案、不同人群疏散荷载下疏散的失效概率.通过对计算结果分析可得:不考虑隧道各项火灾控制与疏散的有利因素,可用安全疏散时间取规范值时,横通道疏散可靠性相对最高,纵横结合逃生方案次之.     

多模式区域公交协调调度模型和算法

考虑公交内部及公交和地铁、长途客运之间的换乘衔接问题,满足最小和最大发车间隔等现实约束因素,建立了一类多目标多模式公交协调时刻表模型,在某时段内分别追求非换乘和换乘出行者在所有站点的等车时间最少和所有车辆到达站点时的泊位数最多.利用约束法将该问题转化为单目标规划问题.根据模型特征,设计求解该问题的改进细菌觅食优化算法,定义解的编码方案,设计产生初始种群的启发式算法,将梯度概念引入移动步长进而改进细菌觅食操作.最后,结合一个简单算例,比较单模式和多模式区域公交协调调度之间的差异,分析了站点通行能力对调度结果的影响,并将该算法与其他智能算法进行了比较分析,从而验证了模型和算法的正确性和有效性.