侧向风下航母甲板风涡流场的模拟研究

采用低马赫数假设下的气流运动控制方程组和湍流大涡模拟方法,研究在侧向来风条件下,航母甲板风涡流场的特点。在侧向来风时,航母前部甲板上方压强时均值、变化幅度与周期差异不大;后部甲板上方压强时均值较前半部分略有增加,变化幅度和周期均有所增大。     

基于PSO-BP神经网络的油船中部结构优化

以舱段质量为目标函数,以相关规范要求的板厚及应力为约束条件,通过灵敏度分析确定设计变量,对油船中部结构优化。构建基于粒子群优化的BP神经网络模型,并代替有限元分析确定应力与设计变量之间关系,从而对舱段进行结构优化。优化后舱段质量降低了4.2%,优化后的有限元分析结果表明满足规范要求,PSOBP神经网络模型在船舶结构优化设计中具有可行性。     

液氨储罐角焊缝在线相控阵检验技术

文中针对液氨储罐定期检验不开罐的特点,通过对相控阵超声成像检测技术的研究,设计了4块角焊缝试板,共8处裂纹缺陷,通过设定检测参数,确定了实验参数和检测方案,检测出了预制的8处裂纹,并与DR检测成像进了比对,得到了较好的检测效果,对于将超声相控阵检验技术用于实际检测具有借鉴意义。     

三维圆柱体绕流数值模拟流场选择及网格划分

文章通过数值模拟结果确定适合的三维圆柱体绕流流场的尺寸,采用不同的计算流体力学(CFD)软件对有限元模型进行网格划分,对比网格划分质量的优劣,选择适合数值模拟的软件CFX。确定采用的网格形式为六面体网格(Hex8)以及流场不同部分网格的尺寸。圆柱绕流展向各截面平均压力系数沿周向无明显变化,脉动压力系数变化显著,绕流后的旋涡发放形式具有明显的三维特性的数值模拟结果验证了本文的流场选择和网格化分尺度的合理性。     

甲板上浪问题的二维数值模拟

以连续性方程和N-S方程为控制方程,采用源造波理论和技术,建立了具有造波和消波功能的二维数值波浪水槽,并使用VOF方法追踪自由面来模拟二维情况下的甲板上浪问题.文中就迎浪状态下的固定FPSO和横浪状态下的运动船体断面模型所遭遇的甲板上浪现象分别进行了数值模拟研究.船体的运动规律通过势流理论计算结果给定,在上浪现象模拟计算时,船体的运动采用移动网格技术实现.研究表明,计算结果与试验结果相当吻合,该方法可以用于甲板上浪现象的预报和模拟,可以用于分析预报甲板上浪对浮体的破坏作用.     

三类边界条件下隔水套管涡激非线性振动的比较分析

考虑流及波流联合作用,研究了套管的涡激非线性振动.将套管简化为梁模型,考虑3类不同的边界条件,计及莫里森非线性流体动力和涡激荷载,建立套管的涡激振动方程.应用克雷洛夫函数求解套管的固有频率和模态,采用了计算涡激非线性动力响应的迦辽金方法.以东海勘探3号钻井隔水套管为例,研究了不同边界条件下流引起的主共振和波流联合引起的组合共振.计算结果表明：流对套管的动力响应占主导地位,而波的影响不大.分析了3类不同边界条件下隔水套管的涡激非线性动力响应,揭示了波流联合激励下套管复杂的动力响应特性.     

Unsteady finite-depth effects during resistance tests on a ship model in a towing tank

This paper covers an extension of the study of Doctors et al. (J Ship Res 52(4):263–273, 2008) on oscillations in wave resistance during the constant-velocity phase of a towing-tank resistance test on a ship model to the case of relatively shallow water. We demonstrate here that the unsteady effects are very prominent and that it is essentially impossible to achieve a steady-state resistance curve in a towing tank of typical proportions for a water-depth-to-model-length ratio of 0.25. This statement is particularly true in the speed region near a depth Froude number of unity. However, on the positive side, we show here that an application of unsteady linearized wave-resistance theory provides an excellent prediction of the measured total resistance, when one accounts for the form factor in the usual manner. Finally, a simple application of the results to the planning and analysis of towing-tank tests is presented.     

某国际集装箱码头给排水设计探讨

结合某国际集装箱码头给排水、消防设计,探讨无市政给排水管网码头区的给水、消防、排水管线的设计,为相似码头工程的设计提供一定的设计思路.     

液化天然气B型独立液货舱结构低周疲劳研究

基于某B型独立液货舱为研究对象,开展液化天然气(LNG)船码头装卸货工况下的结构应力和温度场热应力分析,重点针对液货舱水平强框处连接节点计算其因装卸货受力和温度变化所引起的疲劳累积损伤。研究结果表明,部分研究疲劳节点由装卸货产生的低周疲劳损伤在整个结构疲劳累积损伤中的占比较大,对结构疲劳损伤起主导作用,需要在液货舱疲劳强度分析中予以重点关注。因此,对此类B型独立液货舱进行结构设计必须考虑低周疲劳的影响。     

Property Evolution of Sulphoaluminate Grouting Material under Pressure Circulation北大核心CSCD

Water-sealed underground oil tank projects are quite different from traditional underground projects since the water-sealing conditions are very strict and the difficulties caused by the geological specificity, structural specificity and construction specificity are key factors affecting the project. In light of the significant early initial setting time and rapid temperature increase of sulphoaluminate cement-based grouting material for a large domestic water-sealed underground oil tank with pressurized cyclic grouting, a laboratory grouting simulation is conducted. It is found that the properties of the sulphoaluminate cement-based grouting material are quite different under different pressure cycles, the hydration exothermic peak time gets shorter with an increase of circulation time, the compressive strength decreases with an increase of circulation time, and the longer the circulation time the more obvious the de-crease of compressive strength. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.