不同冷却方式对大尺寸钢板感应加热成形的影响

为有效解决船用中厚钢板复杂曲面加工问题,研究空气冷却(空冷)、正面水冷和反面水冷方式对大尺寸钢板弯曲成形的影响因素。首先采用COMSOL Multiphysics仿真平台模拟电磁感应加热和冷却变形多物理场同步耦合过程,然后分析各种因素对大尺寸钢板弯曲成形的影响,最后通过试验验证有限元模型的可靠性,并对感应加热弯曲成形效果进行评估。结果表明:相对于水冷,空气冷却对钢板Y向位移改变效果显著;相对于空气冷却,水冷对钢板角位移的改变影响明显;当频率为50 k Hz时,电流频率对表面温度和角位移影响显著;当钢板长宽比不小于1∶2时,Y向位移的增加比较显著;当长宽比约为1∶1时,角位移的改变比较明显。     

Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Model Test on Grouting Law in Dynamic Water-Rich Sand Layers by the Electric Resistance Method北大核心CSCD

In order to study the diffusion law of grouting slurry in the water-rich sand layer under flowing water conditions, a grouting test model consisting of a main test system, a grouting system, and a measurement system was developed. And for detecting the diffusion scope of the grouts, a new resistivity method was proposed. It is found that the relationship between grouting pressure and grouting rate during the test is strong. Under hydrodynamic conditions, the grouting slurry diffuses elliptically. Due to gravity and the effect of the upper water flow, the center of gravity of the ellipsoid is below the grouting outlet, and the grouting effectively improves the physical and mechanical properties of water-rich sand bodies. At the same time, the resistivity method has a good application effect on the detection of grouting diffusion range. The range of slurry diffusion obtained by the resistivity method is basically consistent with the boundary of the stone body after excavation, indicating that the resistivity method is reliable for detection of grouting range in dynamic water-rich sand layer. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

油田注水管道的腐蚀研究与缓蚀剂评价

油田注水管线所输送介质复杂,腐蚀现象严重,存在安全隐患,一旦因腐蚀泄漏就会造成巨大的经济损失。因此,开展油田注水管道的腐蚀研究及采取措施减缓腐蚀具有重要意义。为此,对某油田注水管道现场采集注入水样及腐蚀产物,通过X-射线衍射及X-射线能谱仪进行分析,分析结果表明腐蚀产物主要是碳酸钙,同时含有一定量的氯化物、碳酸亚铁、硫化物等成分。通过电镜扫描腐蚀产物的微观形貌,发现存在氯离子腐蚀。并通过ICP-OES分析输送介质组分,针对其腐蚀特点及输送介质组分,采用失重法及电化学方法评价了引入季铵盐的咪唑啉缓蚀剂HJD2最佳质量分数及缓蚀机理,实验结果表明该缓蚀剂对该注水管道具有较好的缓蚀作用,在现场注水温度下,最佳质量分数(0.06%)时的缓蚀效率为95.1%,通过注入该缓蚀剂可以有效地减缓该注水管线的腐蚀,延长管线的使用寿命。     

高速船尾部喷水推进局部振动分析

针对高速船尾部采用喷水推进装置的局部振动问题,建立了船体尾部包含喷水推进泵的有限元模型。考虑附连水质量的影响,将船体尾部离散成甲板,底板,喷水推进泵,尾板等局部结构,采用规范经验公式估算以及有限元分析的方法分别对各局部结构的板、板格、板架进行固有频率计算,将其结果与轴频和叶频激励频率进行储备频率校核,判断尾部采用喷水推进装置在振动问题上是否满足规范标准,并为下一步的船体设计提供参考。     

应用于船舶压载水处理系统的自清洗过滤器技术

介绍了2种用于压载水处理系统的自清洗过滤器的工作原理和技术特点,并结合过滤器陆基试验的测试结果,对这2种自清洗过滤器在3种水质下的过滤效果和反冲洗效果进行分析和总结,结果可为压载水处理系统用的自清洗过滤器设计和选型提供一定参考。     

取水工程对港内水流条件及泥沙回淤的影响

针对取水工程对港池内水流及泥沙影响问题,以黄骅港综合港区港池取水工程为例,通过在分析工程区域自然条件和泥沙条件的基础上建立三维数学模型的方法,从潮流、泥沙角度分析各取水方案对港池内水流条件和泥沙回淤的影响。结果表明:取水工程实施后整个港池内流速均不大,除取水口外,流速均在0.1 m/s以下。取水工程不会造成周边水域泥沙场的改变,对进港航道及港池淤积影响不大。取水工程实施后在设计最大取水流量范围内不会影响港口的正常运行。     

散杂码头设计中节能增效措施的应用

针对码头工程中如何多方位将节能增效措施融入到设计中的问题,以长江江苏段某散杂码头及其堆场的设计为例,在工艺、结构、电气等方面采用多方位比较的方法,工艺采用装船机、取料机和皮带机变频联动系统、旋转式过渡皮带车以及三工位头部伸缩装置等措施,结构方面陆域轨道基础采用新型专利,电气方面采用风光互补路灯及岸电系统等不同的节能增效措施,使项目更经济合理、效益显著。     

宽浅河道低水头水电枢纽口门区通航水流条件研究

根据重力相似准则,采用比尺为1∶100的整体模型,进行某宽浅河道低水头水电枢纽口门区的通航安全性研究。采用ADV三维流速测量系统进行流速测量;采用标准矩形量水堰控制模型流量;采用差动式尾门调节模型水位。由于河道地形及枢纽布置的原因,上游口门区流速过大,下游口门区形成大范围回流。通过扩大河道过流面积,移除下游河道中心连续小岛,增加闸孔等措施,减小下泄水流流速,改善河道整体水流状态;通过加长导航墙,改变导航墙透水面积,优化口门区域地形等措施极大地改善了船闸上下游引航道及口门区通航水流条件,确保过闸船舶的安全。     

船舶稳定计算在浅水倒驳抛石中的应用

针对船舶施工安全稳定性问题,以马来西亚槟城吹填二期（STP2）工程为例,介绍特定条件限制下的浅水抛石施工方法,以施工过程中的船舶稳定性验算为理论基础,判定了船舶的横倾角并通过工程实例验证,为类似工程提供相对简单、实用的船舶安全验算基础。