纤维对微表处混合料性能影响分析

微表处是一种性能优良的养护技术,在我国得到广泛的应用.检验了微表处用原材料的技术指标,在满足规范的要求上以试验分析为基础,通过使用不同纤维以及纤维的添加量,分析这些因素对微表处混合料轮辙变形试验的影响.     

A robust non-Hertzian contact method for wheel–rail normal contact analysis

A modified Kik–Piotrowski (MKP) model is proposed in this paper for an accurate and robust calculation of wheel–rail normal contact problem. The presented method is able to consider the relationship between the elastic deformation of a line and the normal pressure distribution within the contact patch. A novel shape correction method is put forward to correctly describe the elastic deformation of the contact patch. Taking the results estimated by Kalker’s variational method and Kik–Piotrowski method as references, the proposed method is validated by three contact cases, including the assumed standardised non-Hertzian contact and the two-point contact, as well as the contact behaviours based on three actual wheel–rail profiles. The simulation results indicate that, compared with Kik–Piotrowski method, the proposed MKP method achieves better agreement with Kalker’s variational method. Moreover, the MKP method can avoid the abrupt change of wheel–rail normal force due to the sudden transfer of the contact point, which contributes to a better computational stability.     

Field measurements of the evolution of wheel wear and vehicle dynamics for high-speed trains

This investigation demonstrates the wheel wear evolution and related vehicle dynamics of high-speed trains with an operating distance (OD) of around two million kilometres. A long-term experimental test lasting two years was conducted to record the wheel profiles and structural vibrations of various trainsets. The wheel wear, namely the profile shape, worn distribution and wheelset conicity, is investigated for several continuous reprofiling cycles. Typical results are illustrated for the stability analysis, and the ride quality is examined with increasing OD. In addition, the vibration transition characteristics between suspensions are investigated in both the time and frequency domains. The experiments show that the dominant wear concentrates on the nominal rolling radius, and the wear rate increases with OD because of the surface softening resulting from the loss of wheel material. The vibration of structural components is aggravated by the increase of the equivalent conicity of the wheelset, which rises approximately linearly with the wheel wear and OD. High-frequency vibrations arise in the bogie and car body related to the track arrangement and wheel out-of-roundness, causing the ride comfort to worsen significantly. Additionally, the system vibration characteristics are strongly dependent on the atmospheric temperature. Summaries and conclusions are obtained regarding the wheel wear and related vehicle dynamics of high-speed trains over long operating times and distances.     

隧道成型控制爆破技术及围岩损伤范围研究

为解决因初期支护格栅拱架限制周边眼钻凿精度而引起的隧道周边超欠挖问题,以青岛地铁1号线瓦屋庄站至贵州路站区间工程为例,介绍“长、短眼”控制爆破技术,提出“长、短眼”布置方案,并采用质点峰值振动法和激光隧道断面检测仪分别对“长、短眼”爆破技术产生的围岩损伤范围和隧道超欠挖量进行分析和监测。结果表明： 1）采用“长、短眼”控制爆破技术,Ⅳ级围岩段隧道周边超欠挖控制在150 mm以内,且理论计算每米进尺回填混凝土节省成本7 182元,可提高工程经济效益; 2）长短眼爆破产生的损伤范围为0.29~0.33 m,隧道拱顶沉降、净空收敛量均控制在10 mm以内,施工效果好。     

R407C在客车空调中的应用技术

介绍R407C与R134a理论热力循环计算方法;对R407C客车空调系统性能的变化、零部件和材料的选用进行技术分析;为R407C客车空调器的研发设计提供参考。     

轮边减速器行星齿轮机构仿真分析与试验研究

行星齿轮机构是轮边减速器的关键部件。本文以某公司新开发的轮边减速器为模型,在SolidWorks中建立其三维模型,运用ANSYS Workbench有限元分析软件对其进行接触应力分析,查找其薄弱环节。仿真分析结果与台架试验结果基本一致,为轮边减速器的设计提供参考和指导。     

插电式混合动力汽车高电压部件设计及布置

根据整车设计要求,建立插电式双电机MG1/MG2+行星轮系混合动力汽车高电压系统方案模型。通过理论计算及工程分析确定高压电池组、高电压线缆、双电机MG1/MG2、变频器(转换器/逆变器)、空调压缩机等高电压部件的结构及关键参数。针对高电压部件布置的安全及可靠性提出建议。     

基于 M/G/1模型的停车场出口排队延误

通过对大型停车场高峰时段出口车辆行驶特性的调查研究,选取了车辆排队的出口车头时距以及出口服务时间两个指标。基于两个指标实测特性和 M/G/1排队模型的分析,计算了停车场出口理论平均排队时间。通过实测车辆平均排队时间,对理论模型计算的平均排队时间进行了修正。实例分析表明：排队时间修正模型能够准确地估计排队时间。提出了基于驾驶员容忍度的排队延误分级标准。     

高速列车车轮强度快速评价系统研制

为提高高速列车车轮优化设计过程中车轮强度评价的效率,开发了高速列车车轮强度快速评价系统.基于数据库的车轮设计参数,利用ANSYS二次开发技术在ANSYS环境中驱动车轮三维模型的自动重建,以期望的网格密度,完成车轮模型的网格划分,继而按照车轮强度评价标准规定的工况,自动生成相应的强度分析前处理模型.调用ANSYS求解器完成强度仿真分析,最后进行数据后处理得到评价结论.以某型动车组车轮为例,通过人工计算与本文自动计算的结果对比,验证所开发系统的可靠性.     

基于模态试验和有限元模态分析的转向盘怠速抖动改进

针对某车型怠速工况下转向盘抖动问题,对整车进行了怠速振动试验并对转向盘进行了模态试验,确认转向盘系统与仪表板横梁及横梁与车身连接处的连接刚度不足导致整个转向系统模态下降,从而引起了共振。针对该问题建立了转向系统有限元模型,并根据模态试验结果对模型进行了验证。在该模型基础上对上述连接刚度进行了优化,对优化方案进行试验验证的结果表明该方案有效。