STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

An improved cellular automaton with axis information for microscopic traffic simulation

Cellular Automaton (CA), an efficient dynamic modeling method that is widely used in traffic engineering, is newly introduced for traffic load modeling. This modeling method significantly addresses the modest traffic loads for long-span bridges. It does, however, require improvement to calculate precise load effects. This paper proposed an improved cellular automaton with axis information, defined as the Multi-axle Single-cell Cellular Automaton (MSCA), for the precise micro-simulation of random traffic loads on bridges. Four main ingredients of lattice, cells’ states, neighborhoods and transition rules are redefined in MSCA to generate microscopic vehicle sequences with detailed vehicle axle positions, user-defined cell sizes and time steps. The simulation methodology of MSCA is then proposed. Finally, MSCA is carefully calibrated and validated using site-specific WIM data. The results indicate: (1) the relative errors (REs) for the traffic parameters, such as volumes, speeds, weights, and headways, from MSCA are basically no more than ±10% of those of WIM data; (2) the load effects of three typical influence lines (ILs) with varied lengths of 50, 200 and 1000 m are also confidently comparable, both of which validate the rationality and precision of MSCA. Furthermore, the accurate vehicle parameters and gaps generated from MSCA can be applied not only for precise traffic loading on infrastructures but also for the accurate estimation of vehicle dynamics and safety. Hence, wide application of MSCA can potentially be expected.     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。     

冲压机械振动对高铁桥梁及行车动力影响分析

高速铁路桥梁的平顺性和稳定性对运营列车的平稳性和安全性有很大影响。为研究冲压机械产生的外部振动激励对高铁桥梁的影响,首先通过对此机械引起的地面振动进行实测,并结合有限元分析软件,确定最大冲击荷载作用下产生的地面振动及传播至桥墩处的振动;然后通过建立列车-轨道-桥梁耦合动力学模型,将桥墩处的地面振动作为激励输入,分析列车以不同速度通过时车辆、桥梁动力学响应。结果表明:地面冲击振动有限元模型计算结果与实测结果基本相符,验证了模型的可靠性;地面振动对桥梁响应会产生一定的影响,距振源50 m处地面振动对桥梁所产生的影响较距振源80 m处(桥墩处)的大,但对运行车辆的影响很小;随着车速由250 km/h至350 km/h,车辆及桥梁各结构的动态响应均有所增大,但都未超出安全限值。因此,冲压机械冲击作用导致的地面振动对列车-轨道-桥梁系统动态服役性能影响非常有限。     

Time domain analysis procedures for fatigue assessment of a semi-submersible wind turbine

Long term time domain analysis of the nominal stress for fatigue assessment of the tower and platform members of a three-column semi-submersible was performed by fully coupled time domain analyses in Simo-Riflex-AeroDyn. By combining the nominal stress ranges with stress concentration factors, hot spot stresses for fatigue damage calculation can be obtained. The aim of the study was to investigate the necessary simulation duration, number of random realisations and bin sizes for the discretisation of the joint wind and wave distribution. A total of 2316 3-h time domain simulations, were performed.In mild sea states with wind speeds between 7 and 9 m/s, the tower and pontoon experienced high fatigue damage due to resonance in the first bending frequency of the tower from the tower wake blade passing frequency (3P).Important fatigue effects seemed to be captured by 1 h simulations, and the sensitivity to number of random realisations was low when running simulations of more than 1 h. Fatigue damage for the tower base converged faster with simulation duration and number of random realisations than it did for the platform members.Bin sizes of 2 m/s for wind, 1 s for wave periods and 1 m for wave heights seemed to give acceptable estimates of total fatigue damage. It is, however, important that wind speeds that give coinciding 3P and tower resonance are included and that wave periods that give the largest pitch motion are included in the analysis.     

公路地基真空排水预压法探讨

真空排水预压法与堆载预压法相比具有加载快、无需堆载材料、不会失稳等优势,适用于加固软土特别是含水量较高的超软土地基。真空-堆载联合预压法的应用也越来越多。经过国内外十几年的探索,真空排水预压法日趋成熟,已经成为大面积应用的加固软土地基的行之有效的方法之一。     

流线型钢箱梁涡激振动机理与气动控制措施

以某主跨390 m的独塔流线型钢箱梁斜拉桥为工程依托，采用风洞试验与计算流体动力学（Computational Fluid Dynamics，CFD）相结合的方法对流线型钢箱梁涡激振动机理与气动控制措施进行研究。首先，采用几何缩尺比为1∶30的主梁节段模型进行主梁涡振性能与气动控制措施优化研究；其次，采用CFD方法对主梁涡振响应进行流固耦合计算，将Newmark-β算法嵌入ANSYS Fluent用户自定义函数（User Defined Functions，UDFs）实现主梁结构振动响应求解，同时结合动网格技术实现主梁断面流固耦合分析；并根据判断条件来检索箱梁壁面上的网格单元，以获得主梁断面振动过程中的表面压力，然后结合主梁结构振动响应、表面压力以及流场特征等对主梁涡激振动机理进行分析。结果表明：该桥主梁原设计方案存在涡激共振现象，将梁底检修车轨道内移120 cm可有效抑制主梁涡振响应；主梁涡激振动响应的数值模拟结果与风洞试验结果吻合较好；检修车轨道内移120 cm后主要改变了箱梁下表面平均压力系数分布特性，且箱梁表面各测点脉动压力卓越频率不一致，有效减小了主梁涡激振动响应；流线型箱梁靠近迎风侧的“被动区域”对结构涡振响应贡献较小，背风侧“驱动区域”发生周期性旋涡脱落是影响流线型箱梁涡振的主要因素。     

钢檩条设计中的若干问题

轻型屋面钢檩条的竖向荷载、整体稳定性计算以及檩条与屋面梁、屋架的连接构造是设计的重要环节,本文结合规范和国家标准设计图的编制提出若干问题,供参考.     

高墩连续刚构左右幅相连横向抗风分析

高墩大跨径连续刚构桥梁主墩横向抗风设计问题突出,多以增大主墩底部尺寸来解决,但变截面高墩容易造成施工不便和影响美观。对分幅桥梁,笔者认为可将左右幅0#块用外伸横隔板相连,双幅桥梁的主墩共同承担横向风荷载。以龙门大桥为例,用Midas建立单幅桥梁和双幅相连桥梁的两个模型,比较各自的内力和稳定性,再应用ANSYS对受力复杂的0#块及其外伸隔板作三维实体仿真分析。结果表明,双幅桥梁相连后可有效减少墩底内力,提高整体稳定性。