连续刚构箱梁桥的剪力滞效应分析

根据一座单箱三室连续刚构组合桥梁,考虑桩-土相互作用分别建立了变截面三维梁单元和三维实体、板壳单元组合两种有限元模型,分析了桥梁在均布荷载和集中荷载作用下的剪力滞效应,并讨论了两种计算模型对动力特性的影响。结果表明,在均布荷载与集中荷载作用下箱梁的剪力滞效应明显不同,对于地震时程反应分析而言,采用变截面三维梁单元模型计算效率较高。所得的分析结果对指导这类桥梁的设计具有重要的工程实用价值。     

冷铣刨机金属探测技术研究

随着冷铣刨机在路面养护施工中的大量使用,铣刨机金属探测技术的应用显得越来越重要。介绍了金属探测技术方法的选择和金属探测器的应用情况,并通过实验确定了金属探测器安装在铣刨机上的最佳数量、位置和高度。     

斜拉桥最大悬臂阶段抖振响应及其对施工人员影响

对某一斜拉桥进行最大双悬臂和最大单悬臂的空间有限元分析,采用时域分析方法,计算不同阻尼工况下,桥梁在不同攻角风作用下的抖振响应,通过频谱分析,讨论最不利施工状态下桥梁抖振响应对施工人员安全的影响。研究表明:抖振作用下的Diekemann舒适度指标值较大,对施工人员安全和桥梁施工质量均有影响,应采用一定的控制措施。     

Nonlinear three-dimensional wagon-track model for the investigation of rail corrugation initiation on curved track

A nonlinear wagon-track model on curved track has been developed to characterize rail corrugation formation due to self-excitation of the wheel-rail stick-slip process. In this model, wagon movements were described using up to 78 degrees of freedom (DOFs) to model a three-piece freight bogie. Innovatively, the wheelset movements are described using nine DOFs, including torsional and bending modes about the longitudinal and vertical directions. The track modelling is considered as a one-layer structure (two rail beams on discrete spring and damper elements). The wheel sliding after creepage saturation is considered in the wheel-rail interface modelling. Simulation of a case study shows that the frequencies of the wheel stick-slip process are composed of the basic frequency, which might come from the combined effect of sleeper-passing frequency and one-third of the combined torsional and bending frequency of the wheelset, and the double and triple basic frequencies, which form the wavelengths of rail corrugation at different situations.     

抚鲅线喂油泵振动频谱应用

在管输企业内很多机泵是用软性方法对轮胶皮联接的.胶皮具有易损和老化等特性,振动图谱上也不同于刚性联接.以抚鲅线首站喂油泵为例对其进行跟踪研究,发现软性联接具备工频弱化和1.5倍频出现峰值等特点.因此软性联接振动图谱的研究是对目前频谱监测方法的有效补充.     

FEM/BEM在轮胎振动和噪声特性分析中的应用

基于ABAQUS和SYSNOISE程序,给出了分析轮胎振动和噪声特性的有限元和边界元模型及完整方法（FEM/BEM）,并以此模型和方法对某半钢子午胎进行了模态分析,计算其在激励作用下的辐射声场.计算结果表明,只要有通过试验获得的轮胎在滚动过程中所受到的真实激励谱,利用本文的方法即可对轮胎的振动噪声进行预报.     

用MATLAB计算发动机悬置系统的固有频率和主振型

介绍了计算发动机橡胶悬置系统固有频率和主振型的过程,利用MATLAB编程并验证程序的正确性。通过程序的运行,能快速获得悬置振动系统的固有特性,为设计人员判断悬置系统是否会发生共振提供理论依据,也为进一步分析系统的响应打下了必要的基础。     

CFC复频电导法与TEM瞬变电磁法在某隧道中的应用对比

CFC复频电导法与TEM瞬变电磁法是我国目前较为先进的隧道超前探水技术。以CFC与TEM在我国某铁路隧道中的应用为例,简述CFC与TEM的方法原理,并结合开挖实际情况进行对比。试验对比表明,CFC探水技术抗干扰能力更强,探水预报结果更为准确,特别是在电磁环境复杂的隧道。     

变频调速技术在催化裂化装置机泵中的应用

简要介绍了变频调速技术,重点分析了与阀门调节相比,变频调速器的节能效果,比较了变频调速器应用前后机泵的运行周期和采用阀门调节与变频调速调节两种方式的节能效益,同时分析了控制方案的不同对节能效果的影响.     

Parameters optimisation of a vehicle suspension system using a particle swarm optimisation algorithm

The purpose of this paper is to determine the lumped suspension parameters that minimise a multi-objective function in a vehicle model under different standard PSD road profiles. This optimisation tries to meet the rms vertical acceleration weighted limits for human sensitivity curves from ISO 2631 [ISO-2631: guide for evaluation of human exposure to whole-body vibration. Europe; 1997] at the driver's seat, the road holding capability and the suspension working space. The vehicle is modelled in the frequency domain using eight degrees of freedom under a random road profile. The particle swarm optimisation and sequential quadratic programming algorithms are used to obtain the suspension optimal parameters in different road profile and vehicle velocity conditions. A sensitivity analysis is performed using the obtained results and, in Class G road profile, the seat damping has the major influence on the minimisation of the multi-objective function. The influence of vehicle parameters in vibration attenuation is analysed and it is concluded that the front suspension stiffness should be less stiff than the rear ones when the driver's seat relative position is located forward the centre of gravity of the car body. Graphs and tables for the behaviour of suspension parameters related to road classes, used algorithms and velocities are presented to illustrate the results. In Class A road profile it was possible to find optimal parameters within the boundaries of the design variables that resulted in acceptable values for the comfort, road holding and suspension working space.