钢轨廓形优化对转辙器动力特性的影响研究

为提高列车高速直向过岔平稳性,将60N钢轨廓形及新设计的尖轨廓形应用于18号高速道岔转辙器部分,应用车辆-道岔耦合动力学理论,建立模型进行动力学仿真计算,与CHN60高速道岔转辙器动力特性进行对比。仿真计算结果表明:60N高速道岔转辙器部分轮载过渡段起点前移,轮载过渡时间增长;车辆直向经过道岔转辙器时的滚动圆半径差、轮对横移量和钢轨横向接触点外移幅值均减小,轮对蛇形运动幅度减小,行车平稳性得到提高;轮轨最大横向力由6.12 kN降低至4.75 kN,轮轨横向相互作用力减弱;车轮脱轨系数、车体横向加速度略有减小,轮轨垂向力、车轮减载率和车体垂向加速度变化不大,均在安全范围内。     

屈服假塑性流体管流流动及传热规律研究

结合屈服假塑性流体的本构方程、管流力平衡关系式以及非牛顿流体的能量方程，得出了屈服假塑性流体管流速度分布及温度分布。研究结果表明：由于屈服应力的作用，管中心存在柱塞流动，柱塞的半径与屈服应力成正比，与压力梯度成反比；管流流量随屈服应力的增大而减小；柱塞内温度一致，从柱塞边界到管壁，温度逐渐减小，而且越靠近管壁，温降梯度越大。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

The influence of fully nonlinear wave forces on aero-hydro-elastic calculations of monopile wind turbines

The response of an offshore wind turbine tower and its monopile foundation has been investigated when exposed to linear and fully nonlinear irregular waves on four different water depths. The investigation focuses on the consequences of including full nonlinearity in the wave kinematics. The linear and nonlinear irregular wave realizations are calculated using the fully nonlinear potential flow wave model OceanWave3D [1]. The linear and nonlinear wave realizations are compared using both a static analysis on a fixed monopile and dynamic calculations with the aeroelastic code Flex5 [2]. The conclusion from this analysis is that linear wave theory is generally sufficient for estimating the fatigue loading, but wave nonlinearity is important in determining the ultimate design loads.     

基于Femap的风帆基座局部强度分析

以上海海事大学教学实习船"育明"轮为对象,研究船舶加装风帆装置的船体结构强度问题,通过局部加强风帆基座和船体连接部分来保证风帆安装部位的结构稳定性。利用Solidworks和Femap软件建立了风帆基座和船体的有限元模型,计算得到该模型在10级风载荷下受风角度从0°~60°的应力和应变。最终结果表明,在10级风载荷下,该船风帆基座和局部加强后的船体的强度符合要求。     

Spar基础浮式风机系泊系统全耦合分析

本文以OC3 Hywind Spar基础浮式风机为研究对象,采用先进的空气动力-水动力耦合时域分析方法,针对其在中国南海某海域风浪流共同作用下,系泊系统、浮式基础运动以及风机与塔桶载荷响应进行分析。对比了定常风与湍流风模型对浮式风机系泊系统、整体运动响应以及风机载荷的影响。计算结果表明：相比于湍流风,采用定常风进行浮式风机系泊系统分析将得到偏于危险的结果,同时浮式风机运动响应与风机载荷结果偏小。本文建议在系泊系统初始设计阶段采用定常风方法进行设计,在系泊分析阶段采用湍流风进行分析,以保证浮式风机长期服役安全。     

风积砂填筑路基施工质量控制

通过工程实践,介绍采用风积砂填筑路基的施工工艺和质量控制过程。     

BINGHAM流体环空管流流动及传热规律研究

结合BINGHAM流体的本构方程、管流运动方程及能量方程 ,推导了BINGHAM流体环空管流速度分布及温度分布。由于BINGHAM流体具有屈服值 ,环空管流流动中会形成流核。流核的宽度与屈服应力成正比 ,与广义压力梯度呈反比。流核中心线偏离环空中心线 ,且偏向环空内侧。环空内外径之比越小 ,相对偏离越远。在其他条件不变的情况下 ,当屈服应力增大时 ,速度分布剖面变得愈扁平。当其他条件不变时 ,流核速度随环空内外径之比减小而增大。流核内温度变化比环空内外侧明显小 ,随屈服应力的增大 ,温度分布剖面愈扁平。     

一种进一步降低轿车空气阻力的方法

本文首先简要地分析了声激励减阻机理，然后，针对类似桑塔纳车身的模型采用了声激励的方法进行了减低空气阻力的研究，得出了声激励参数，方式和减阻效果的关系，并且对此进行了一定的分析，表明利用声激励方法可以进一步降低此类车身的空气阻力。     

T形、X形桑性路面平面交叉口竖向设计探讨

探讨了T形、X形柔性路面平面交叉口竖向设计，分析了平交口连接部的纵断设计及平交口竖向高程的调整，从而达到合理的交叉口竖向设计。