排序方式: 共有45条查询结果,搜索用时 171 毫秒
1.
J. A. Sparenberg 《Journal of Marine Science and Technology》1997,2(2):53-61
The axial force induced on a duct (duct thrust) which surrounds a propulsor is, by means of an energy conservation argument,
expressed in terms of the thrust and power of the propulsor and the kinetic energy losses per unit of time of the propulsor
and the duct. Emphasis is put on the linear theory of an axisymmetric ducted actuator disk, where it is shown that the work
done by the duct thrust is equal to the extra work done by the actuator disk when it is surrounded by the duct. This simplified
model gives more insight into the interaction between the propeller and the duct and on the limits of linearization. 相似文献
2.
基于滑移网格方法,采用SST k-ω湍流模型研究不同网格划分方式对带前置定子导管式推进器非定常性能的研究。首先基于相对参考坐标系法及滑移网格方法分别对推进器在定常与非定常下的性能进行数值预报,并与试验结果相比验证计算方法的可靠性。基于该方法研究整体网格划分方式与周期性网格对推力系数、扭矩系数与推进器各个方向上的非定常脉动力的影响。研究结果为进一步研究推进器非定常性能提供了参考。 相似文献
3.
4.
Jungyong Wang Ayhan Akinturk Neil Bose Stephen J. Jones Yun Young Song Ho Hwan Chun Moon Chan Kim 《Journal of Marine Science and Technology》2008,13(3):244-255
The objective of this study was to investigate the performance of a model azimuthing podded propulsor in ice-covered water.
Model tests were carried out with two different depths of cut into the ice (15 and 35 mm), two different ice conditions (presawn
and pack ice conditions), and four different azimuthing angles. The depth of cut is the maximum penetration depth of the propeller
blade into the ice block. The 0.3-m-diameter model propeller was operated in a continuous ice milling condition. Ice loads
were measured by several sensors which were installed in various positions on the model. Six one-axis pancake-style load cells
on the top of the model measured the global loads and two six-component dynamometers were installed on the shaft to measure
the shaft loads. One six-component dynamometer was attached to the one of the propeller blades inside the hub to measure the
blade loads. The pod unit and propeller performance in ice are presented. Ice-related loads, which were obtained when the
blade was inside the ice block, are introduced and discussed. During the propeller–ice interaction, a blade can experience
the path generated by the previous blade, which is called the shadowing effect. The effects of shadowing, depth of cut, azimuthing
angle, and advance coefficient on propulsor performance are presented and discussed. 相似文献
5.
6.
基于某艇的推进性能需求,以喷水推进器设计工况为分析对象,采用计算流体力学(Computational Fluid Dynamics,CFD)方法,建立计算模型,研究叶轮叶顶间隙、流道格栅密度、艇底水底间距、双泵轴间距等工程应用因素对推进性能的影响,可为某艇喷水推进器的设计、安装与使用等提供合理依据。 相似文献
7.
在文献[1]的基础上,提出了评价船后组合推进器推力减额特性的4个指标:整体推力减额效率(1-t1)、转子推力减额效率(1-t2)、组合推进器推力比τ和导管定子阻力比γ.利用CSSRC现存试验数据运用简单对比和统计分析方法,给出了诸设计参数对这些指标影响的显著性和规律性.推荐采用受控于全部主参数的指标(1-t2)作为船体与组合推进器相互干扰特性优化的总目标,提出了用部分主参数控制的对应分目标优化和迭代来实现总目标优化的简明策略.实例计算表明,优化设计船体尾型主参数LRD、CPR和推进器主参数(A)ex/AP的搭配,可大幅度提高船后组合推进器的推力减额效率. 相似文献
8.
9.
船体与组合推进器水动力相互干扰特征的模型试验及推力减额特性的评估分析 总被引:1,自引:1,他引:0
以船体、导管和前置定子及转子组成的系统的推力减额特性为研究对象,基于因子分析理论,提出了该三因子系统的水动力相互干扰分析模型,导出了诸因子之间相互影响的求解公式,并采用分解试验方法实现了所有效应的准确测定.分析研究了系统推力减额的两种不同处理方式,建立了相应的评价指标体系.通过对两个特定方案的评估分析,推荐采用k2和t2作为系统推力减额性能优劣的综合评价指标,并建议采取以减小RrlH和RrlSD为主要方向的优化策略. 相似文献
10.
吊舱式电力推进船舶螺旋桨匹配设计仿真研究 总被引:2,自引:0,他引:2
在国内,吊舱推进器的设计还处于理论起步阶段,尤其是吊舱推进器螺旋桨,其设计方法尚未成熟,而螺旋桨的设计对于整个推进系统推进性能的影响又尤为关键,关系到船—机—桨匹配的综合推进性能。为此,采用常规螺旋桨敞水特性图谱等效设计POD螺旋桨参数的方法对吊舱推进器螺旋桨进行设计,分析吊舱式推进船舶船—机—桨的匹配性能。为了提高设计效率及优化推进系统的推进性能,针对吊舱式电力推进船舶,采用常规螺旋桨等效设计方法设计POD螺旋桨参数,同时基于LabVIEW图形化编程语言开发船—机—桨匹配数值分析软件以对设计参数进行静态匹配计算,并与母船的推进效率进行对比,选取最优化的螺旋桨参数作为POD螺旋桨参数,以优化推进效率。研究结果表明:采用常规螺旋桨等效设计方法设计POD螺旋桨参数的方案,同时结合开发的船—机—桨匹配数值仿真分析平台,可以方便、快捷地对吊舱式推进船舶进行船—机—桨匹配分析计算比较,提高推进性能。 相似文献