舰用ICR燃气轮机PSR瞬态响应特性的数值分析

基于能量守恒原理和PSR（一次表面回热器）的结构特点，导出回热器冷热流体和固体问壁非稳态温度变化的微分方程式；利用直观的流动扰动因子M修正传热系数k，研究热流体进口温度和流量发生阶跃变化时PSR的响应时间；还分析了PSR传热波纹板片的数目，1、几何尺寸及通道波纹形状对温度响应时间的影响。研究结果表明，由于PSR的固体壁面时间常数远小于板翅式和管壳式换热器，因此这种轻重结构的先进换热器响应特性明显优于常规热交换器，特别适用于那些要求机动多变、反应灵敏的舰船和车用燃气轮机动力装置。     

海上单桩风力发电平台简化设计

采用在欧洲已经进行商业化运作的独立桩双段结构，桩基础采用带有过渡段的单桩。塔架上的风力发电机采用丹麦Vestas公司的V80风力发电机。参考DNV-OS-J101和API-RP-2A中的工作应力设计法，进行结构静力、桩基础的承载力，涡激振动、疲劳寿命，结构动力学等分析。静力分析分析极端环境下的组合工况；桩基础主要计算桩的轴向承载力和校核水平承载力，并采用有限元模型模拟桩土相互作用；涡激振动分析主要考虑不同风速下塔架的升力以及引起的横向振动；疲劳分析根据涡激振动分析的结果利用S-N曲线对基础寿命进行了评估；动力学分析求出了结构的固有频率，并进行了波浪力作用下的瞬态历程分析。     

水下爆炸作用下船舶结构与燃气轮机动态响应的数值研究

本文对水下爆炸作用下舰船结构及燃气轮机结构冲击响应进行了数值研究.首先,基于CEL方法建立了近自由面水下爆炸流固耦合动力学模型.然后结合燃气轮机-船体一体化仿真分析方法,对不同水下爆炸工况下的舰船结构冲击环境,以及燃气轮机冲击损伤特性进行了评估分析,总结了工况参数对燃气轮机冲击响应特征的影响规律,旨在为舰用燃气轮机抗冲击设计提供技术参考.     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

计及叶片载荷的双机对转式海流发电机系泊系统动力分析

本文设计了一种新型的双机对转式海流发电机并对其系泊系统与叶片载荷和直径关系进行模拟分析。首先将单机式海流发电机与已有研究进行对比验证其可靠性，然后在不改变系泊方式的前提下，设计出双机式结构，并通过分析机身位移和旋转比较两种系统的稳定性。为考虑叶片载荷对系泊系统影响，在Orcaflex中对不同精细程度的叶片进行建模，分别对比单一翼型/三翼型/九翼型的数值模拟结果。接着使用M-BEMT软件优化后的翼型参数，对比使用原始升阻力系数的三翼型发电机的模拟结果，同时将使用不同直径叶片的发电机系统进行对比，说明双机式发电机的稳定性更优，对海流发电机及其系泊系统的设计提供重要参考价值。     

某型汽轮机超速脱扣试验浅析

某型汽轮机的超速保护装置采用脱扣结构,文章针对该汽轮机的超速脱扣结构进行分析,总结此种超速脱扣装置的装配要求和试验方法,以利于该型汽轮机的生产。     

The influence of fully nonlinear wave forces on aero-hydro-elastic calculations of monopile wind turbines

The response of an offshore wind turbine tower and its monopile foundation has been investigated when exposed to linear and fully nonlinear irregular waves on four different water depths. The investigation focuses on the consequences of including full nonlinearity in the wave kinematics. The linear and nonlinear irregular wave realizations are calculated using the fully nonlinear potential flow wave model OceanWave3D [1]. The linear and nonlinear wave realizations are compared using both a static analysis on a fixed monopile and dynamic calculations with the aeroelastic code Flex5 [2]. The conclusion from this analysis is that linear wave theory is generally sufficient for estimating the fatigue loading, but wave nonlinearity is important in determining the ultimate design loads.     

轴流式涡轮机动叶片的叶顶间隙对其气动性能影响

采用数值方法对不同叶顶间隙下某型号船用轴流式涡轮机的气动性能进行了对比分析.结果表明,叶顶间隙对喷嘴环前缘的压力分布和涡轮内的温度分布影响明显,过小和过大的叶顶间隙都会导致喷嘴环前缘高压力区的产生,并导致涡轮内局部高温度区域扩大;随着叶顶间隙的增大,喷嘴环后缘底部、吸力面及叶顶间隙内局部高熵区随之增大,燃气能量损失增大.     

抽气式涡轮帆的气动力学分析研究

介绍了抽气式涡轮帆的结构和工作原理,使用Gambit软件建立了涡轮帆的模型,并采用RNG k-ε湍流模型描述了涡轮帆的动力学特性。利用Fluent软件对抽气式涡轮帆进行了数值模拟计算,并与风洞试验数据进行了对比,升阻力系数的模拟结果与试验数据变化趋势基本一致。计算了特定情况下椭圆筒不同偏转角时的升阻力系数,并模拟了不同旋转角下吸气强度以及旋转角为0°时分流板位置对涡轮帆升阻力系数的影响,为涡轮帆的优化选择提供了依据。     

基于Femap的风帆基座局部强度分析

以上海海事大学教学实习船"育明"轮为对象,研究船舶加装风帆装置的船体结构强度问题,通过局部加强风帆基座和船体连接部分来保证风帆安装部位的结构稳定性。利用Solidworks和Femap软件建立了风帆基座和船体的有限元模型,计算得到该模型在10级风载荷下受风角度从0°~60°的应力和应变。最终结果表明,在10级风载荷下,该船风帆基座和局部加强后的船体的强度符合要求。