Critical review of handling diagram and understeer gradient for vehicles with locked differential

The steady-state cornering behaviour of rear-wheel drive vehicles fitted with locked differential is critically analysed by means of simple, albeit carefully formulated, vehicle models, which allow for a rigorous theoretical analysis. Results obtained for some classical manoeuvres, with either constant forward speed, steer angle or turning radius, clearly show that, in the case of locked differential, the vehicle cornering behaviour is strongly affected by the manoeuvre. As an important consequence, the handling diagram is not unique and the understeer gradient is no longer dependent only upon the lateral acceleration, as in vehicles equipped with an open differential. Accordingly, this study shows that some typical tools and concepts of vehicle dynamics are indeed inadequate in the case of locked differential.     

基坑开挖引起复合地基下卧双线地铁隧道附加荷载的计算研究

为研究基坑开挖时复合地基及竖向、横向"双洞效应"对下卧双线地铁隧道竖向、横向附加荷载的影响,基于Mindlin应力解,得到在复合地基侧摩阻力作用下隧道轴线上的竖向、横向附加荷载,通过迭代法计算得到"双洞效应"引起隧道轴线上的竖向、横向附加荷载,借助竖向、横向总附加荷载引起的隧道位移对比验证,并分析隧道位置改变对侧摩阻力和"双洞效应"引起隧道竖向、横向附加荷载的影响。研究结果表明:侧摩阻力和"双洞效应"对隧道竖向、横向附加荷载的影响是不可忽略的,其影响主要表现为减小隧道的竖向、横向总附加荷载,且影响范围不变;在施工条件和规范容许范围内,应尽量减小双线隧道之间的距离,以及增大隧道与基坑中点的距离;当需要严谨精确地计算小净距地铁隧道"双洞效应"引起的附加荷载时,必须选用迭代法计算。     

桥头搭板结构分析

将桥头间搭板简化为具有局部脱空的Winkler地基梁，针对不同的端部支承条件，对它在移动车辆荷载作用下的受力状况进行了全面分析，绘制了几种典型搭板的最大弯矩影响线图，给出了可用于搭板设计的诺模图。     

浅析连续箱梁设计中的几个问题

结合工程实际,对连续箱梁设计计算中常遇到的几个棘手问题进行定量分析,并给出工程中实际可用的计算方法。     

基于图像分析的滚动轴承表面缺陷识别技术研究

系统介绍了滚动轴承表面缺陷视觉检测系统的检测原理及流程,着重分析了表面缺陷二值图像的几何特征和形状矩特征、BP神经网络的各参数选择以及实验结果．实验证明本系统用于滚动轴承表面缺陷检测具有可行性,采用神经网络识别可使表面缺陷分类正确率达到88％．     

“穷举法”在油船货油舱分舱优化设计中的应用

为实现油船货油舱分舱优化,以一艘大型油船为例,根据MARPOL公约和共同结构规范(HCSR)的要求,在主尺度、船型和货油舱总舱容确定的情况下,以最小静水弯矩为优化目标,基于"穷举法"编制优化货油舱横舱壁位置的应用程序。实际应用结果表明,该程序可运用到油船的分舱优化中,能达到快速、合理地分舱,提高设计效率的目的。     

大断面异形盾构隧道弯矩传递系数原型加载试验研究

由于异形盾构隧道特殊的结构断面型式,管片设计暂无相关规范可循,故基于原型三环管片力学加载试验对异形盾构管片环向接头弯矩传递系数进行研究,研究结果表明:1)随埋深增加,异形盾构管片结构整体刚度提升,但由于各接头刚度与相邻管片结构刚度比随埋深增加变化规律不一致,异形盾构管片接头弯矩传递能力呈部分减弱部分增强的现象;2)同埋深条件下,随着侧压力系数的增加,除右拱腰处接头外,其余接头弯矩传递能力随着接头刚度与相邻管片结构刚度比的增大而逐渐增强;3)随着埋深增加,各接头弯矩传递能力对侧压力系数的敏感程度逐渐减弱;4)极限破坏后,异形盾构管片内外弧面裂缝的分布规律证明了明显的弯矩传递现象。     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

CSR-H与CSR强度评估载荷的对比研究

对CSR-H 与CSR用于强度分析的载荷变化进行分析,对各载荷分量的包络值以及应用于等效设计波中的船体梁波浪弯矩、波浪剪力和外部海水压力、加速度等载荷分量的大小进行比较。分析货油舱、干散货舱、压载舱典型位置处的内部压力变化,并对载荷变化可能引起的结构要求变化进行分析和概括。     

中长周期波浪条件下船舶航迹带宽度研究

针对现行《海港总平面设计规范》中航迹带宽度计算在中长周期波浪条件下存在的不足,对比分析国外航道规范中的研究成果,并通过船舶操纵模拟试验等技术手段,运用船舶外缘包络线法统计分析了不同航速、不同吨级的散货船在各种中长周期波工况下的航迹带宽度,给出了中长周期波浪条件下的波浪附加宽度参考值,并与国外规范中的设计取值进行了对比.