自激多谐继电器稳定可靠性的提高措施

针对闪光器普遍存在闪频不稳的现象，分类叙述影响自激多谐继电器闪频的因素，并提出提高其稳定可靠性的具体措施。     

坞式舰船压载系统研究

对坞式舰船压载系统设计中需考虑的稳性、作业时间、注排水方式等问题进行了分析研究,可供有关设计人员参考.     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

1-50m钢混结合梁施工过程中的稳定性分析

利用SAP84计算程序和根据设计规范手算相结合 ,对 15 0m钢混结合梁施工过程中开口截面钢梁的稳定性进行分析比较 ,介绍建模及计算过程 ;同时根据计算结果 ,揭示结构的薄弱环节 ,并依此检验为防止结构失稳而采取的结构构造措施     

B_0-B_0机车转向架直线运行横向轮/轨力和蛇行稳定性的理论研究(上)

本文根据轮/轨蠕滑理论提供了计算和分析B_0—B_0机车转向架直线运行横向轮/轨力的方法,并以SS4型电力机车作为验证实例,理论计算和实际测试的结果相接近。作者采用这种方法对轮/轨力进行可靠的分析,旨在论证我国现有电力机车转向架蛇行稳定性所要求的最佳轮对定位刚度。本文论证结果符合于作者在文献[1]中提出的轮对定位新方案,它可适用于最大运行速度为100km/h的现有SS型电力机车。     

天津港突堤转角处高桩码头后承台构件相对错位破损原因

近几年天津港多个突堤转角处的高桩码头岸坡变形比较明显,导致码头后方承台结构构件出现明显的相对错位、变形等破损情况,严重影响了码头结构物安全。通过对破损状况的调查统计,总结出了破损的特点,对破损的原因进行了理论分析,并用原型观测和数模计算结果进行了验证。原型观测结果表明:码头岸坡内的淤泥质粘土层为水平位移最明显土层,靠近挡土墙的大部分桩顶都出现了不同程度的向陆侧倾斜,这与实际见到的桩端倾斜状况完全相符。数模计算结果除验证了原型观测的结果以外,还发现仅在后方堆场堆载工况为最危险情况,是造成岸坡变形和后方承台构件相对错位的主要原因。     

船舶浮态计算方法及船舶浮态图谱

本文用化非线性问题为线性问题的线性化方法,对非线性隐式的船舶浮态方程组进行了数值解,并在深入研究的基础上提出了两种形式浮态图谱,以便能迅速而准确地确定船舶各种不同装载情况下的浮态。本文给出了五万吨油轮“西湖”号算例。     

悬挂式单轨车辆走行轮失效对曲线通过及运行平稳性影响的仿真分析

悬挂式单轨车辆走行轮在车辆运行中起到承载和传力的重要作用,其走行轮失效对悬挂式单轨车辆运行性能有重大影响。通过多刚体动力学理论建立悬挂式单轨车轨耦合动力学模型,仿真分析了不同工况下走行轮失效对单轨车辆曲线通过及运行平稳性的影响。仿真结果表明:空载状态下走行轮失效的悬挂式单轨车辆在曲线半径100 m的线路上限速为35 km/h,而满载状态下走行轮失效的车辆一直处于不安全状态,需要尽快行驶到就近站点疏散乘客;同侧走行轮失效对单轨车辆的影响趋势基本一致;在相同行车速度下,走行轮失效时竖向平稳性指标出现了部分数值超过3.0的情况,说明走行轮失效时车辆的运行平稳性会变差。仿真研究结果可为走行轮失效的悬挂式单轨车辆运行提供参考。     

The Reinforcement Analysis of Prestressed Anchor Frame Beam in the Deep Cutting Slope under Three Dimensional Strong EarthquakeEI北大核心

Research purposes: In order to further study the reinforcement of prestressed anchor frame beam in the deep cutting slope under three dimensional strong earthquake, a model of the deep cutting slope is built through FLAC 3D simulation software, the seismic wave to the model from three directions of x,y and z is input, and the dynamic response of the slope is analyzed. Then, the prestressed anchor frame beam reinforcement measures are applied to the model, and this paper analyzes the reinforcement effect of the prestressed anchor frame beam to the deep cutting slope under three dimensional strong earthquake. Research conclusions:(1) The prestressed anchor frame beam has a good effect on restraining the horizontal displacement of the deep cutting slope. (2) Under the three dimensional strong earthquake, the prestressed anchor frame beam has a good effect on the horizontal acceleration and horizontal velocity of the deep cutting slope, which reduces the peak of horizontal acceleration and horizontal velocity. (3) Through the comparison of the response before and after the reinforcement of the prestressed anchor frame beam is given under the 9 degrees three dimensional strong earthquake, it can be concluded that the prestressed anchor frame beam can provide good reinforcement effect to the deep cutting slope. (4) This research can be used for reference to the earthquake resistance of the slope engineering. © 2018, Editorial Department of Journal of Railway Engineering Society. All right reserved.     

104型分配阀制动性能不良问题的分析及探讨

通过分析长沙车辆段2009年两制动室检修的104型分配阀返修原因及运用客车制动阀性能不良的故障现象,提出了104型分配阀检修及试验的改进措施。