奥迪A5打不着车

<正>车型:奥迪A5,发动机和变速器型号分别为CDNB、0AW。VIN:WAU8FD8T0AA××××××。行驶里程:58635km。故障现象:此车为进水车辆,但已作过拆检处理。拖车拖至公司,打开机舱盖,目视未发现异常,检测机油油位正常,燃油表正常,启动发动机,启动机能正常启动,但是没着车迹象。启动时,经测量油压,发现油泵不工作。     

宝马523Li油表不准后部车窗升降故障

<正>车型:F18,配置N52T发动机。行驶里程:49718km。故障现象:客户反映油表不准及后部车窗升降有故障。故障诊断:根据客户的反映,检查确认油表不准及后部车窗升降有故障,另外还有空调不制冷、雨刮器不停的刮且无法停止等故障现象。使用诊断仪ISID检测,有很多故障码,相关的故障码如下:驾驶员侧后部车窗升降机:不能对◆驱动装置进行初始化设置3010F前乘客侧后部车窗升降机:◆     

关于车辆燃油箱取油方案的技术改进

针对目前车辆燃油箱在取油时,采用连接法兰的方案对燃油箱本体造产生了严重的焊接变形,笔者通过分析焊接法兰方案找出不足,提出了新的改进方案。     

一种船用低硫油冷却系统电气控制设计

根据国际公约对燃油含硫量的要求,设计了一种低硫油冷却系统,介绍其组成并具体地分析了电气原理图。此系统已应用于生产实际,性能达到预期效果,有一定的参考价值。     

嵌入式油船排油监控系统的设计

以基于ARM Cortex^(TM)-M3内核的STM32F107VCT6微处理器为硬件平台,将μC/OS-II嵌入式实时操作系统移植到微处理器之上,搭建了系统软件开发平台,开发出排油监控系统控制器,集数据采集、GPS定位、分析计算、指令执行、数据存储、记录打印等功能于一体。给出了控制单元具体的软硬件实现方法,在.Net开发环境下利用Visual C#编程语言完成计算机监控软件的构建,实现了与控制单元的通信。在油船货油装卸模拟系统的运行结果表明,该排油监控系统可满足国际海事组织(IMO)关于油船排油监控系统的有关要求。     

汽车铝油冷器内颗粒冲蚀磨损分析方法研究

基于实际运行过程中固体颗粒对铝油冷器的冲蚀磨损,建立了采用有限元分析的颗粒冲蚀数值计算模型。模型充分考虑了颗粒浓度、冲击参数、材料等因素的影响,得到了某铝油冷器产品固体颗粒轨迹图,进而预测该产品磨损量最大的位置。     

基于FTA的船用分油机跑油故障分析

文章基于一次船舶分油机跑油的故障处理,介绍了运用故障树分析法对分油机跑油现象的分析过程。通过故障树计算出导致分油机跑油事件的概率,并对故障概率高低进行分析,以便快速而准确地查找。     

船用滑油在线检测传感器选型研究

通过对国内外滑油在线检测技术的分析,针对某型船用滑油油品、磨粒、水分在线检测传感器的选型要求,从传感器的性能指标、安装方式等方面进行了分析研究,并对选出的传感器做了仿真分析,最终确定了传感器的选型。     

16V280ZJ型机车柴油机用纵向进油喷油器的设计与仿真

对16V280ZJ型柴油机螺栓调整式喷油器进行了纵向进油改进设计,从而减少燃油在高压管路内的压力损失,提高燃油喷射压力,改善柴油机性能.完成纵向进油喷油器的设计,运用AutoCAD软件绘制新型纵向进油喷油器的零件图和装配图;利用Fluent软件对改进部位改进前后的三维流场分别进行数值模拟计算,得到流场的压力云图,对比分析计算结果;利用GT-Fuel对改进前后的柴油机进行仿真模拟并对仿真结果进行对比分析,总结其合理性并得出结论.     

Experimental study on frictional and sealing performances of packing rings in an oil-free gas compressor

To enhance the reliability and to extend service life of packing rings, tribological and sealing performances are investigated based on the experimental results. Friction force, leakage rate and power consumption of three materials of pressure packing seals are measured in a refitted vertical gas compressor. The rings are made of common filled polytetrafluroethylene (Filled PTFE), PTFE reinforced with 30% mass fraction carbon fiber (30%CF+PTFE), and carbon-carbon composites infiltrated with PTFE (C/C+PTFE), respectively. It is found that packing rings will periodically vibrate with the periodic vibration of pressure packing after the travel direction of motion abruptly turns to the reverse direction. Furthermore, the amplitude of vibration slows down with the increasing crank angle. Approximate value of friction force is available by multiple-point fast Fourier transformation (FFT) employed to process the experimental results by reducing the impact of vibration to a great extent. Of three materials of rings employed in experiments, Filled PTFE presents minimal leakage rate accompanied with maximum power consumption. And 30%CF+PTFE exhibits minimum friction power and moderate leakage rate. As for C/C+PTFE, its high mechanical and thermal properties are favorable factors to enhance the ability of operating under high pressure and velocity and to improve the wear resistance. Unfortunately, this also leads to a large leakage rate. Comprehensive consideration should be taken into to evaluate the availability, reliability and service life for a type of packing ring under dry running conditions.