船舶总振动固有频率实用算法

分别用一维梁有限元方法和三维有限元方法计算3艘实船总振动固有频率,对计算结果进行统计分析,提出对一维梁有限元方法计算结果的修正,利用110000t油船进行验证。用一维梁有限元方法计算时考虑剪切滞后影响系数;用三维有限元方法计算时,是在ANSYS软件中建立全船的三维空间有限元模型,进行模态分析。通过计算证明该方法能有效改进一维梁有限元计算方法,可快速准确地预报船舶总振动固有频率。     

基于Simulink/Stateflow的汽车ABS混合建模与仿真

汽车防抱死制动系统(ABS)是一种很关键的汽车主动安全技术。本文采用基于有限状态机的系统仿真方法,采用Simulink和Stateflow模块混合建模,对ABS模型中的连续系统和离散系统进行仿真。仿真结果表明,该混合仿真系统能比较真实地反映汽车ABS系统的实际工作过程,显著缩短制动距离,提高安全性。     

Rhinoceros软件在客车造型设计中的应用

介绍造型设计软件Rhinoceros,并以豪华大客车为例,讲述该软件在客车CAS(计算机辅助造型设计)中的应用。     

大跨桥梁实测湍流风场的大涡模拟

为实现在大涡模拟(LES)中准确评估强风湍流对大跨桥梁的作用,关键难点在于生成符合桥梁真实强风特性的入口湍流。为此应用了一种新的规则化波矢量随机流生成方法PRFG³(Prescribed-wavevector Random Flow Generator),该方法遵守连续性方程和泰勒假设,可准确模拟目标湍流的脉动风谱、湍流度和湍流积分尺度等风特性参数。首先利用西堠门大桥结构健康监测系统(SHMS)2016年内采集的风速数据,选取了该桥址区10 min时距平均风速较大但风特性不同的2个强风样本,分析得到相应的强风特性参数;然后采用PRFG³方法合成了符合上述2个实测强风特性的均质各向异性湍流,同时为验证该方法用于主梁节段模型LES入口湍流的适用性,还模拟了缩尺比为1∶50的强风湍流场,并基于OPENFOAM平台,将3类风场赋予LES入口进行了数值计算;最后将LES流场中多个监测点的湍流特性与实测结果进行了对比。研究结果表明：2个实测风场在顺风向、横风向、竖风向的脉动风谱均与Von Kármán谱接近,顺风向湍流积分尺度最大约为192 m,各脉动风...     

面向驾驶模拟器的高等级公路三维视景建模与实现

随着汽车驾驶模拟器在道路交通仿真中的广泛应用,驾驶员对视景的逼真度也相应地提出了较高的要求。视景仿真系统作为模拟器的一个子系统,其逼真度和实时的动态显示是影响道路交通仿真的关键因素。文中介绍了高等级公路三维视景的建模过程、实现方法,以及地形的简化技术。设计成果表明,这种方法对于利用驾驶模拟器进行道路交通仿真等方面的研究是可行的。     

Within day rescheduling microsimulation combined with macrosimulated traffic

The concept of rescheduling is essential to activity-based modeling in order to calculate effects of both unexpected incidents and adaptation of individuals to traffic demand management measures. When collaboration between individuals is involved or timetable based public transportation modes are chosen, rescheduling becomes complex. This paper describes a new framework to investigate algorithms for rescheduling at a large scale. The framework allows to explicitly model the information flow between traffic information services and travelers. It combines macroscopic traffic assignment with microscopic simulation of agents adapting their schedules. Perception filtering is introduced to allow for traveler specific interpretation of perceived macroscopic data and for information going unnoticed; perception filters feed person specific short term predictions about the environment required for schedule adaptation. Individuals are assumed to maximize schedule utility. Initial agendas are created by the FEATHERS activity-based schedule generator for mutually independent individuals using an undisturbed loaded transportation network. The new framework allows both actor behavior and external phenomena to influence the transportation network state; individuals interpret the state changes via perception filtering and start adapting their schedules, again affecting the network via updated traffic demand. The first rescheduling mechanism that has been investigated uses marginal utility that monotonically decreases with activity duration and a monotonically converging relaxation algorithm to efficiently determine the new activity timing. The current framework implementation is aimed to support re-timing, re-location and activity re-sequencing; re-routing at the level of the individual however, requires microscopic travel simulation.     

(Unintended) Transport impacts of an energy-environment policy: The case of CNG conversion of vehicles in Dhaka

Motor vehicles are one of the major sources of air pollution in Dhaka, the capital of Bangladesh. The government took various policies to convert the petroleum vehicles on road to run on compressed natural gas (CNG), which allows both air quality improvements and energy security benefits. One of the market friendly policies to encourage the fuel switch was to increase the price differential between CNG and petrol and diesel. This has allowed a wide-scale adoption of CNG as the fuel of choice. However, several years into the policy, there is now a widespread belief among the policymakers that the CNG conversion may have increased car ownership and car travel due to their lower running costs, resulting in more congestion and a reversal of the strategy is on the cards. It is therefore important to test the hypothesis whether CNG conversion had genuinely increased car ownership and car travel in Dhaka city. This paper presents the results of a questionnaire survey and an econometric intervention analysis to understand the impact of CNG conversion on car ownership and car travel in Dhaka. Attention is also given to disentangle the self-selection and price-induced travel effects of CNG conversion. Results show that ownership did not increase, but travel of on-road vehicles increased due to the CNG policy. However, additional congestion costs are still around one half of the health benefits brought about by the policy.     

智能马达控制中心在海洋平台设计中的应用

介绍一种利用新型智能电机过载继电器E3 PLUS、现场通信总线DeviceNet及PLC等技术相结合的船舶智能马达控制系统,阐述智能马达控制中心(Smart MCC)的工作原理、功能及应用实例,该系统可以提供电机多种故障检测和诊断功能以及计算机集中控制,使马达控制系统逐步向自动化集成型发展,系统的性能和可靠性高,能最大限度地降低船舶整体运行成本,提高运行效率.     

Privacy protection method for fine-grained urban traffic modeling using mobile sensors

With the ubiquitous nature of mobile sensing technologies, privacy issues are becoming increasingly important, and need to be carefully addressed. Data needs for transportation modeling and privacy protection should be deliberately balanced for different applications. This paper focuses on developing privacy mechanisms that would simultaneously satisfy privacy protection and data needs for fine-grained urban traffic modeling applications using mobile sensors. To accomplish this, a virtual trip lines (VTLs) zone-based system and related filtering approaches are developed. Traffic-knowledge-based adversary models are proposed and tested to evaluate the effectiveness of such a privacy protection system by making privacy attacks. The results show that in addition to ensuring an acceptable level of privacy, the released datasets from the privacy-enhancing system can also be applied to urban traffic modeling with satisfactory results. Albeit application-specific, such a “Privacy-by-Design” approach would hopefully shed some light on other transportation applications using mobile sensors.     

汽油机活塞组—气缸套整体耦合传热模型及应用

采用直接耦合的有限元分析方法对一汽油机的活塞组—气缸套系统的瞬态传热过程进行了研究。通过将润滑油膜假设为一维热阻,建立了活塞组—气缸套整体耦合系统的三维传热模型,应用所开发的三维流体动压润滑分析程序对活塞环组沿周向瞬时变化的油膜厚度进行了计算与分析。以LJ377MV汽油机活塞组—气缸套零部件为对象进行了应用研究,获得了更为清晰的多部件间的相互传热关系。