利用钢轮托车辅助盾构机过站施工技术

针对地铁盾构法施工中盾构机通过满足过站要求的已完工车站进行二次始发这一常见施工环节,介绍一种通过钢轮托车辅助盾构机空载推进实现过站需要的施工技术及相应施工要点,如盾构机过站的施工工艺流程,钢板、钢轮拖车及轨道的铺设等。论述了利用钢轮拖车辅助盾构机过站施工技术采取的质量控制、安全措施及环保措施,分析了采用该技术的经济、社会和环境效益。     

变频器输出电压du/dt对电机的影响及其滤波器的设计

研究了变频器输出电压du/dt对电机端电压和轴承电流的影响,在PSpice中建立了电机高频模型,并对端电压波形进行了仿真;着重研究了一种du/dt滤波器的参数设计方法,并且进行了仿真和实验验证。实践证明,该滤波器具有较好的滤波效果。     

CARD/1系统在互通立交设计绘图上的应用与开发

通过对CARD/1系统在T型（Y型）互通式立体交叉设计绘图上的二次开发，使T型（Y型）互通式立体交叉的设计绘图达到一体化。     

超大跨度缆索承重桥梁结构体系

设计和建造跨海连岛大桥是新世纪桥梁工程面临的巨大挑战。超大跨度桥梁并不只是常规概念的外推,需要与之对应的结构体系。从根本上改变缆索承重桥梁的缆索体系,可以突破跨度极限。本文指出了常规结构体系向更大跨度发展的制约因素,从缆索体系的角度介绍了超大跨度斜拉桥、悬索桥以及斜拉 悬索组合桥可能采用的各种体系。这些体系试图在静力、动力方面能远远超出现有限制范围,极大地提高桥梁的跨越能力。同时,新体系的采用也给材料、设计和施工提出了很大的挑战。     

索力测定常用公式精度分析

本文分析了常用的频率法测定索力公式的精度。利用作者建立的拉索非线性有限元法分析程序,可得到对应特定索力的拉索频率分布,基于此频率分布,采用不同的索力公式可推算出对应的索力。通过对比所得索力与设定索力可判断各公式的精度。本文以某斜拉桥的拉索为例,对处于不同张紧程度、不同长度的拉索进行了分析。分析结果给出了频率法测定索力时的注意事项,以及各公式的适用范围,并推荐了一种高精度的索力推算公式。     

悬索桥主缆线形的鞍座影响

提出了一个基于数值解析法的悬索桥主缆线形计算方法,能全面考虑各种鞍座影响,可用于成桥状态、空缆状态和施工阶段等各阶段的主缆线形分析。通过算例分析了鞍座对主缆线形的影响,计算表明,由于直接约束着主缆的变形,鞍座对主缆线形,特别是施工阶段的主缆线形有较大的影响。计算还表明,本文方法具有考虑因素全面、计算精度高、速度快、使用方便等优点。     

武汉阳逻长江大桥施工猫道设计与验算

扼要介绍了武汉阳逻长江大桥施工猫道的设计,采用ANSYS的LINK10与BEAM4单元计算了猫道这一柔性空间索桁结构在空索状态及成形状态的线形。在静力验算时,猫道中间标高处等效静阵风风速取为50.4m/s,由于主要承重结构钢丝绳弹性模量为索力的函数,本文参考国内多座桥梁施工猫道钢丝绳弹模实测值取用1.30×105MPa,按5种工况8种状态验算了猫道的静风稳定性验算。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

R/S分析法在盾构下穿机场过程中的地表变形规律研究

为保证机场的正常运营,在盾构下穿机场的施工过程中,对地表沉降变形控制的要求较高,因此对穿越过程中的施工控制和变形规律研究具有重要意义。首先,基于盾构下穿机场的工程条件,分析盾构下穿过程中的风险,并提出相应的控制措施;同时,根据现场监测数据,分析盾构下穿机场过程中的地表沉降变形规律,并利用R/S分析法对地表沉降的发展趋势进行研究。结果表明:盾构施工引起的机场地表变形均在控制值范围以内,且各监测点在不同序列条件下的Hurst指数均大于0.5,具有沉降持续减弱的趋势,验证下穿过程中风险控制措施的有效性,为类似下穿机场的盾构施工提供一定的实践经验,也为盾构施工引起的地表沉降变形规律研究提供参考。