钢管-钢管混凝土复合拱桥实桥静载测试与分析

进行了第一座钢管 - 钢管混凝土复合拱试验桥--福建福鼎山前大桥实桥静载测试和有限元模拟分析,对钢管-钢管混凝土复合拱静力性能进行了讨论,研究表明,复合拱的静力性能与等截面拱相近,但拱肋变截面处应变应是设计中的控制因素,极限承载力分析应考虑双重非线性的影响.     

某钢管混凝土系杆拱桥静荷载试验

某主跨52m的钢管混凝土系杆拱桥,建成后因外观质量较差而进行了现场实桥承载能力静荷载试验,利用3辆型号相同的集装箱卡车,测试该桥跨中和4分点处的荷载横向分布系数、各控制截面主要测点的应变影响线以及在基本荷载作用下各控制截面主要测点的应变、挠度等。本文简要介绍了该桥的静荷载试验的全过程,并对测试结果进行了整理分析。     

大跨度钢管混凝土窄拱桥的设计实践探索

以大连理工大学桥梁工程研究所近年来设计的钢管混凝土拱桥为工程背景,介绍了在大跨度窄桥设计、施工中所采用到的一些新的设计方法,对大跨度钢管混凝土窄拱桥的关键技术问题、尤其是拱桥稳定性问题进行了深入地研究分析,结论表明单片桁架式钢管混凝土拱桥在大跨度窄桥中应用是合理的,并且具有一定的优越性。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

南昌生米大桥总体设计

生米大桥是南昌市外环快速道上的城市桥梁，全长3880m，简要介绍生米大桥的项目概况、建设条件、总体布局、技术标准、技术特点、关键技术、科学研究等有关情况。     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

轨道客车不锈钢车体电化学钝化工艺研究

文章通过显微组织、显微硬度、电化学性能表征测试,分析了不锈钢车体焊缝及热影响区的组织变化及性能差异,研究了钝化道次、移动速度等电化学钝化工艺参数对焊接接头及热影响区耐蚀性的影响规律.试验结果表明:焊接热影响区显微组织发生明显改变,显微硬度下降,表面耐蚀性明显下降,当以10 mm/s单道次钝化作业时,点蚀电位最高,耐蚀性最好,30天盐雾试验后,钝化处理表面未发现明显锈蚀.该工艺已在公司进行了推广应用,效果良好.     

R/S分析法在盾构下穿机场过程中的地表变形规律研究

为保证机场的正常运营,在盾构下穿机场的施工过程中,对地表沉降变形控制的要求较高,因此对穿越过程中的施工控制和变形规律研究具有重要意义。首先,基于盾构下穿机场的工程条件,分析盾构下穿过程中的风险,并提出相应的控制措施;同时,根据现场监测数据,分析盾构下穿机场过程中的地表沉降变形规律,并利用R/S分析法对地表沉降的发展趋势进行研究。结果表明:盾构施工引起的机场地表变形均在控制值范围以内,且各监测点在不同序列条件下的Hurst指数均大于0.5,具有沉降持续减弱的趋势,验证下穿过程中风险控制措施的有效性,为类似下穿机场的盾构施工提供一定的实践经验,也为盾构施工引起的地表沉降变形规律研究提供参考。     

跃龙门隧道多功能钢拱架安装机快速施工配套技术

隧道施工机械化是我国隧道施工的发展方向。相较于开挖、衬砌机械化的快速发展,钢拱架安装机械化水平存在不足,长期以来较多采用人工作业,施工人员多、劳动强度大、施工效率及安装精度低,同时存在很大的安全隐患。本文通过跃龙门隧道机械化配置配套应用,分析了钢拱架安装机在机械化快速施工体系中的关键作用,并详细介绍了XZGMT411多功能钢拱架安装机相关参数、施工操作要点及注意事项。多功能钢拱架安装机的使用大幅提高了隧道施工效率及施工质量,缩短了施工工期。     

船舶低硫柴油系统设计的分析与优化

就新辟航线首制船“汉亚直达”集装箱船的低硫柴油系统,叙述了船舶低硫柴油系统的设计经验,从当前国内外对船用燃油硫含量的要求、应对方案到船舶低硫柴油冷却方式选择、低硫柴油冷却系统设计、高/低硫柴油转换、使用低硫柴油风险分析及处理等方面进行详细叙述,为业内同行提供参考。