变频器输出电压du/dt对电机的影响及其滤波器的设计

研究了变频器输出电压du/dt对电机端电压和轴承电流的影响,在PSpice中建立了电机高频模型,并对端电压波形进行了仿真;着重研究了一种du/dt滤波器的参数设计方法,并且进行了仿真和实验验证。实践证明,该滤波器具有较好的滤波效果。     

现代有轨电车智能控制系统中的车辆定位技术方案

从现代有轨电车实际需求出发,参照沈阳市浑南新区现代有轨电车一期工程设计及建设经验,着重介绍现代有轨电车信号系统中的正线道岔控制系统、运营调度辅助系统等设计方案,可为后期国内及国际有轨电车信号系统设计提供借鉴。     

现代物流位置服务系统的设计

介绍了一个用于现代物流业的位置服务系统LTLBS，并着重就系统设计中的关键技术和与现代物流业有关的问题进行了分析。针对现代物流的特殊应用，在LTLBS中设计了一些特殊的功能，如货物跟踪，到达时间估计等。系统的性能分析表明定位精度和数据传输时延完全满足要求。     

CARD/1系统在互通立交设计绘图上的应用与开发

通过对CARD/1系统在T型（Y型）互通式立体交叉设计绘图上的二次开发，使T型（Y型）互通式立体交叉的设计绘图达到一体化。     

理想条件下路网临界车头间距的研究

基于经典的跟驰理论，建立理想条件下车辆稳定跟驰行驶时的车头间距模型。并且利用高精度的车载GPS系统在北京市路网上采集的数据对该模型进行标定。同时根据最优化的相关理论确定出北京市路网达到其理想容量时车辆的临界行驶速度及临界车头间距，从而为确定理想路网容量奠定基础。     

汽车无线电导向行驶系统

介绍GPS系统概况、GPS全球卫星定位系统的基本原理及固定电台汽车导向行驶系统。     

基于WebGIS车辆定位系统的设计

探讨了如何利用WebGIS技术实现在Internet环境下车辆定位中的应用,包括系统的组成、工作原理、短消息和WebGIS架构等内容,该设计方法是在微软最新的开发环境.Net和Mapinfo公司的MapX控件基础上开发实现的,详细解释了WebGIS架构和介绍了车辆定位系统的主要功能。系统的实现使用户可以直接在Internet环境下完成查询指定车辆的位置等相关信息,为智能交通的实现奠定了基础。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

R/S分析法在盾构下穿机场过程中的地表变形规律研究

为保证机场的正常运营,在盾构下穿机场的施工过程中,对地表沉降变形控制的要求较高,因此对穿越过程中的施工控制和变形规律研究具有重要意义。首先,基于盾构下穿机场的工程条件,分析盾构下穿过程中的风险,并提出相应的控制措施;同时,根据现场监测数据,分析盾构下穿机场过程中的地表沉降变形规律,并利用R/S分析法对地表沉降的发展趋势进行研究。结果表明:盾构施工引起的机场地表变形均在控制值范围以内,且各监测点在不同序列条件下的Hurst指数均大于0.5,具有沉降持续减弱的趋势,验证下穿过程中风险控制措施的有效性,为类似下穿机场的盾构施工提供一定的实践经验,也为盾构施工引起的地表沉降变形规律研究提供参考。