潜艇耐压船体破坏载荷预测的一种新方法

本文提出了用灰色系统理论预测破坏载荷的计算方法,并通过新的高强度钢材环肋圆锥壳的球壳模型实验验证了该方法的正确性,建议今后在模型实验和现役潜艇的耐压船体寿命估算中采用这种方法。     

A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side     

基于生长算法构建Delaunay三角网的研究

提出了一种基于凸包构建Delaunay三角网的算法,它包括离散点数据的三角剖分及将约束边嵌入三角网。在对离散点数据进行三角剖分时,首先建立一个外轮廓为凸包的初始三角网,然后将剩余的点依次与既有三角网合并来生成包含所有数据点的三角网。为了将约束边嵌入三角网,找出约束边穿过的三角形,删除这些三角形并用约束边将这些三角形所围成的多边形分成两个简单多边形,再对这两个简单多边形进行Delaunay三角网剖分即可达到嵌入约束边的目的。     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

基于NFFD 算法的船体几何变形技术

本文以非均匀有理B样条基函数作为参数体属性,并结合非均匀控制点网格,建立了适用于船体几何的NFFD变形技术。重点阐述了NFFD方法的基本原理和变形规则,并以矩阵表示方法为基础构建了数学模型。研究了控制点数量和分布对变形结果的影响,增加了控制点变形几何的能力并获得了更大的设计空间。最后,以某CNG运输船为例完成了球鼻艏、船艏和船艉部分几何的自动变形。本文的工作为船型优化提供了良好的变形工具。     

FLNG总体设计关键技术研究

阐述了集天然气预处理、液化、储存、外输为一体的新型海上浮式装置FLNG总体设计中的几项关键技术。提出控制船体运动性能的重要性,从主尺度选择、线型设计和典型配载工况等方面入手进行分析,确定250,000m3 FLNG船体主尺度,以确保上部生产系统高效率的正常作业。针对LNG货物围护系统,提出薄膜型(双排舱)和SPB独立舱型两种货物围护系统方案,并从上部模块支墩设置和隔离舱加热等方面对这两个方案进行比较。论述FLNG冷却海水供应系统的特点及其与常规海底门取水方法的不同之处,提出舷外海水提升泵取水的可行方案。     

基于参数化船型的阻力优化研究

船型几何模型的参数化表达,是船型多学科设计优化的基础。其作用是为各学科分析和优化提供一个统一的几何模型,并根据各学科分析结果自动修改调整船体型线。文中尝试使用Friendship进行船体完全参数化建模,并使用该软件中的feature编程功能编程实现shipflow型值数据的提取;通过改变一系列重要的船型参数实现变换船型几何模型,以获得满足性能需求的船型。最后利用该软件的优化框架,采用切线搜索法 (Tangent Search, TSearch) 完成1300TEU集装箱船的兴波阻力优化,优化球首和前体船体曲面。结果表明,该参数化方法在改进船型水动力性能方面有很好的效果。     

复杂载荷作用下船体板格屈曲强度计算公式研究

分析复杂载荷作用下船体板格结构屈曲强度的影响因素,基于ANSYS软件APDL模块参数化建模,对这些因素进行相关性分析,排除无关参数,保留有关参数,得到屈曲强度的定性表达式。然后变更有关参数,得到不同的有限元模型,通过计算得到不同模型下的屈曲强度,分析大量数据,最终得到屈曲强度的定量表达式。该公式可以在工程上用于复杂载荷作用下船体板格结构的屈曲评估,具有重要的实用价值。     

协调版共同结构规范对20.6万吨散货船的影响评估

以20.6万吨散货船为例,通过描述性规定与直接强度计算,对比分析协调版共同规范与油船共同规范的差异,评估新规范对目前散货船结构可能带来的影响。     

水下爆炸气泡载荷作用下船体梁的动态水弹性响应

文章基于势流理论,针对水下爆炸气泡脉动载荷作用下船体梁的动态水弹性鞭状响应及其共振效应进行了研究。阐述了水下爆炸气泡与船体梁之间的流固耦合理论分析,并分别建立了一个考虑气泡迁移,自由面效应和气泡阻力的气泡模型和一个船体梁的弹性响应的计算模型。文中以两条实船作为算例,研究了刚体运动对船体梁弹性振动响应的影响,分析了船体梁在气泡脉动载荷作用下产生的共振破坏的机理。