环境可持续集装箱班轮运输管理研究综述

集装箱班轮运输业如何在追求成本经济性和服务可靠性的同时做好环境可持续性,对航运企业、港口运营商以及政府组织都提出了新的挑战。围绕集装箱班轮运输在环境层面实现可持续发展的目标,本文分别从战略、战术和运营等3个层面就措施、技术和规章制度等所做的研究进行文献综述、分析发展趋势。战略层面,从市场减排机制和政策的制定、绿色政策、...     

某航道桥下部结构受船舶撞击后安全性能评估及修复

为评估航道桥下部结构的船撞安全性,以遭受船撞的某内河航道桥为研究对象,采用有限元方法和相关规范计算受撞击的5号桥墩自身水平抗力、船撞力、墩顶位移,并从墩顶位移和桥墩抗力两方面对受撞桥墩的安全性进行评估。结果表明:5号桥墩的横桥向和顺桥向抗力均由桩基强度控制,分别为2528 kN和1142 kN;事故船撞击工况下,墩顶最大横桥向和顺桥向位移分别为7.6 mm、13.4 mm,满足位移限值要求;沿横桥向和顺桥向的船撞安全系数分别为1.67和0.94,顺桥向的自身抗力不足以抵抗瞬时船撞力,导致桥墩桩基础受损,建议采用增大截面法对受损桩基础进行加固补强,并设置独立防撞墩以保障桥梁结构安全。基于分析过程,总结了桥梁下部结构船撞安全评估的一般流程。     

Ultimate strength of container ships subjected to combined hogging moment and bottom local loads part 1: Nonlinear finite element analysis

This paper is the first of two companion papers concerning the ultimate hull girder strength of container ships subjected to combined hogging moment and bottom local loads. In the midship part of container ships, upward bottom local loads are usually larger than the downward ones. This leads to the increase of biaxial compression in the outer bottom plating and the reduction of the ultimate hull girder strength in the hogging condition. In this Part 1, the collapse behavior and ultimate strength of container ships under combined hogging moment and bottom local loads are analyzed using nonlinear finite element method. Buckling collapse behavior of bottom stiffened panels during the progressive collapse of a hull girder is closely investigated. It has been found that major factors of the reduction of ultimate hogging strength due to bottom local loads are (1) the increase of the longitudinal compression in the outer bottom and (2) the reduction of the effectiveness of the inner bottom, which is on the tension side of local bending of the double bottom. The obtained results will be utilized in the Part 2 paper to develop a simplified method of progressive collapse analysis of container ships under combined hogging moment and bottom local loads.     

37 500 m3 LEG船液罐吊装精度数字仿真分析

以37500 m³液化乙烯气(Liquefied Ethylene Gas,LEG)船货舱区液罐吊装为研究对象,对液罐吊装前的干涉检查和数据匹配等工作进行梳理,建立一套完整的液罐吊装模拟匹配流程,并对实际吊装过程出现的问题提出解决方案,旨在为后续同类大型液罐的吊装提供参考、积累经验。     

基于粒子群优化反步法的船舶航向控制器设计

考虑到反步法在随机干扰下具有较优的控制效果,利用反步法设计基于Nomoto模型的船舶航向控制器;设计一种基于粒子群优化(Particle Swarm Optimization,PSO)反步法的航向控制器,其能通过优化不确定增益参数来消除部分冗余控制。通过仿真试验比较不同航向控制器的性能。仿真结果表明:粒子群优化反步法航向控制器具有更高的控制精度和更强的鲁棒性。     

12000 t抬浮力打捞工程船电力系统

针对12000t抬浮力打捞工程船,在概括介绍其船型特点的同时,对其电力系统以及在系统设计时需要注意的一些问题进行了详细描述,为同类电力系统设计提供参考.     

船坞水上双岛合拢工艺设计

为了提高公司船坞搭载效率，缩短船舶建造周期，根据南通象屿船坞现有情况，决定将6.35万吨散货船分为两半岛在坞内同时搭载：一总段（从船艉至FR71-1400）;二总段（从FR71-1400至FR96-2000）建造搭载完毕后两总段起浮，并于水上进行两个总段定位连接成整体，定位连接好后落于指定坞墩位置，然后进行两个总段的合拢焊接。此工艺在国内还不多见，具有较高的技术含量，分段在内场建造时，应有严格的建造工艺流程，要保证涉及到合拢分段的建造质量和精度要求。     

乌江思林和沙沱升船机船舶超吃水可行性研究

针对乌江思林、沙沱两座升船机船舶1.6 m吃水控制标准导致载货量偏低的实际问题,开展超吃水船舶进出升船机船厢系统性的实船试验,论证船舶吃水标准提升的可行性。结果表明,船舶出厢为控制性工况,2.0 m吃水船舶正常出厢实测最大下沉量16.46 cm,富余水深大于30 cm;基于实船试验数据改进的下沉量预测公式,将船舶实际下沉量预测精度提高1倍以上;按目前2座升船机运行水位协调机制,上下游水位变化在10 cm以内,船舶最大吃水提升至2.0 m是可行的。建议在运行中按照1.8~2.0 m吃水逐步放宽控制标准。     

铝合金在邮轮主船体结构上的应用分析

基于铝合金与钢结构“等强、等刚、等稳定性”的理论和有限元计算方法的分析,对某邮轮主体结构进行替代等效分析,论证了铝合金结构的安全性、经济性以及可能性,为铝合金在邮轮主船体结构的应用和直接计算方法提供建议和参考。     

Valuation mismatch and shipping q indicator for shipping asset management

ABSTRACT

This paper aims to develop an adaptation of the Tobin Q investment model for the shipping asset management in order to monitor valuation mismatch and bubble pricing of shipping assets. In this circumstance, the market prices of various shipping assets (e.g., Capesize or Panamax dry bulk carriers in different age profiles) are compared to the measured long-term asset value with second-hand ship prices. The mark-to-market prices of shipping assets are led by current market trends and freight rates, while the long-term asset value is estimated by using past data under certain assumptions (mean reversion, trend reversion). The discrepancy between market prices and the long-term nominal value of a shipping asset reflects any mispricing, which in turn sheds light on investment timing and market entry-exit decision.