大直径钢管桩承载力恢复过程试验研究

针对目前预制桩承载力恢复特性研究与工程应用中的不足,依托西非某海工工程,提出高应变法。采用对同一钢管桩进行初打与不同休止时间复打相结合的试验方法,研究了大直径钢管桩沉桩后的承载力恢复过程。结合地质情况、沉桩与试验结果,得到了钢管桩承载力、侧阻力及端阻力随时间变化的一般规律及影响因素,并通过静载试验对研究结果进行了验证。该研究在提高项目施工效率、降低成本的同时,还得到了有意义的规律与结论,可为后续类似项目提供参考。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

Experimental investigation of evaporation rate and exhaust emissions of diesel engine fuelled with cotton seed methyl ester and its blend with petro-diesel

An experimental study to measure the evaporation rates, engine performance and emission characteristics of cotton seed biodiesel (cotton seed oil methyl ester) and its blends in different volumetric proportions with diesel is presented. The thermo-physical properties of all the fuel blends have been measured and presented. Evaporation rates of neat cotton seed biodiesel, neat diesel and their bends have been measured under slow convective environment of air flowing with a constant temperature. Evaporation constants have been determined by using the droplet regression rate data. The neat fuels and fuel blends have been utilized in a test engine with different load conditions to evaluate the performance, combustion and emission characteristics of the fuels. The specific fuel consumption values of the two blends, viz. B25 and B75 are found to be same. At the highest load, B0 records the lowest CO volume followed by B100. From the observed evaporation, performance and emissions characteristics, it is suggested that a blend of B50 and B75 can be optimally used in standard diesel engine settings.     

桥梁模板施工技术应用性研究

桥梁模板是桥梁施工中的重要工具。通过搜集国内外桥梁模板资料,研究总结并提出解决模板工程在桥梁施工中存在各种问题的办法,将对提高工程质量、加快施工速度、提高劳动生产率、降低工程成本和实现桥梁工程的文明施工起到一定的推动作用。     

含碎石化层的沥青加铺路面结构分析

利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500～1000MPa.     

高速铁路轨道的波阻抗及影响因素研究

高速铁路轨道在雷击或故障冲击电流作用下会产生暂态冲击过电压,该过电压的大小由轨道的波阻抗决定。通过建立高速铁路线路的仿真模型,分析直角冲击波在轨道上的传播与折反射过程,提出轨道的波阻抗的计算方法,研究钢轨类型、土壤电阻率、钢轨对地过渡电阻对波阻抗的影响。结果表明:P60型轨道波阻抗数值为235. 55Ω;轨道的波阻抗主要受钢轨类型和土壤电阻率的影响,高速铁路轨道的波阻抗在在210～250Ω变化;在高速铁路轨道仿真模型中,线路末端电阻等于波阻抗时,可以有效地消除折反射对仿真结果的影响,末端电阻的取值不需要考虑钢轨地过渡电阻的影响。研究给出高速铁路轨道波阻抗的范围及仿真模型中末端电阻的取值方法,可以为轨道过电压计算、分析与仿真提供理论与方法参考。     

硅胶吸附管采集甲醇汽车尾气排放中甲醇的方法研究

文章主要研究了利用硅胶吸附管采集甲醇汽车尾气排放中甲醇的方法,对硅胶吸附管的规格、待测样品的浓度、采样参数等进行了详细的讨论及验证。研究表明,利用硅胶吸附管采集甲醇的过程中,很容易发生甲醇的穿透。随着硅胶颗粒装填数目的增加,甲醇的穿透率降低,实际吸附甲醇的效率增加。在采样流量相同时,待测样品浓度越高,甲醇的穿透率越高。在待测样品浓度相同时,采集流量越高,甲醇的穿透率越高。将硅胶吸附管串联,可以有效减少甲醇的穿透,提高吸附效率。     

基于隧道检测钢筋分布不均状况下判定衬砌结构安全性应用研究

近年来隧道内出现的越来越多的质量安全事故,引起各方高度重视,相应的最适宜隧道主体工程衬砌质量控制的地质雷达无损检测方法被广泛应用。通过雷达无损检测可揭露出衬砌内欠厚、脱空、钢筋分布不均等大量各类型缺陷,针对欠厚脱空等缺陷制定的注浆或开窗等治理措施是目前工程中常见的整改闭合工序,但钢筋分布不均对结构安全影响如何判定,怎么界定处理尚无成熟方案与规定。本文针对隧道项目中实际检测出的钢筋分布不均缺陷,在不宜大范围扰动结构及围岩进行整治的情况下,以及在避免其他问题共存等不利因素的前提下,应用有限元数值模拟计算分析强度安全系数,并结合现场外观等综合因素对衬砌结构安全性进行分析判定研究。     

Balancing energy consumption and risk of delay in high speed trains: A three-objective real-time eco-driving algorithm with fuzzy parameters

Eco-driving is an energy efficient traffic operation measure that may lead to important energy savings in high speed railway lines. When a delay arises in real time, it is necessary to recalculate an optimal driving that must be energy efficient and computationally efficient.In addition, it is important that the algorithm includes the existing uncertainty associated with the manual execution of the driving parameters and with the possible future traffic disturbances that could lead to new delays.This paper proposes a new algorithm to be executed in real time, which models the uncertainty in manual driving by means of fuzzy numbers. It is a multi-objective optimization algorithm that includes the classical objectives in literature, running time and energy consumption, and as well a newly defined objective, the risk of delay in arrival. The risk of delay in arrival measure is based on the evolution of the time margin of the train up to destination.The proposed approach is a dynamic algorithm designed to improve the computational time. The optimal Pareto front is continuously tracked during the train travel, and a new set of driving commands is selected and presented to the driver when a delay is detected.The algorithm evaluates the 3 objectives of each solution using a detailed simulator of high speed trains to ensure that solutions are realistic, accurate and applicable by the driver. The use of this algorithm provides energy savings and, in addition, it permits railway operators to balance energy consumption and risk of delays in arrival. This way, the energy performance of the system is improved without degrading the quality of the service.     

柴油发动机掺烧生物柴油的经济性研究

为了更好地评价柴油机燃用生物柴油的经济性,分析了生物柴油和0#石化柴油的理化性质,分别对生物柴油的体积分数为0.2,0.5,1的B20、B50、B100 3种燃料和0#柴油在495Q3柴油机上进行了试验。试验结果显示燃用3种燃料的燃油消耗率比0#柴油在中小负荷时平均增加5.30%,9.65%,19.04%,大负荷时平均增加2.86%,4.75%,9.64%;能量等值折合油耗率在中小负荷时平均增加2.65%,2.63%,5.74%,大负荷时平均降低0.26%,1.97%,4.80%。