钢管混凝土单圆管标准拱桥面外稳定性有限元分析方法研究

为给钢管混凝土单圆管拱桥面外稳定性分析提供实用计算方法,对钢管混凝土单圆管标准拱桥面外弹性稳定性有限元分析方法进行研究。首先使用统计学方法,统计分析国内25座钢管混凝土单圆管拱桥基本构造数据及统计学参数;其次根据已有统计数据建立50~59m、60~69m、70~79m共3类跨径钢管混凝土单圆管标准拱桥并验算其安全性能;给出弹性稳定系数分析标准拱桥面外弹性稳定性能的基本假定以及竖向荷载和横桥向荷载计算方法,采用不同有限元方法分析标准拱桥面外稳定性,确定标准拱桥面外稳定性有限元计算方法。结果表明:通过统计数据建立的钢管混凝土单圆管标准拱桥能反映工程实际;采用恒、活载稳定系数计算方法求解标准拱桥面外弹性稳定承载力及极限承载力较为合适。     

Effect of pitting corrosion on local strength of hold frames of bulk carriers (2nd Report)—Lateral-distortional buckling and local face buckling

Pitting corrosion is typical corrosion observed on coated hold frames of bulk carriers which exclusively carry coal and iron ore. In order to secure the safety of these types of bulk carriers, it is important to understand the effect of pitting corrosion on local strength of hold frames.

In order to investigate this effect, a series of 4- and 3-point bend tests on structural models which consist of web, shell and face plates has been carried out. Artificial pitting was created on the web plate to simulate pitting. In the 4-point bend tests, two equal concentrated loads have been applied vertically at the one-third points of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, lateral-distortional buckling occurred before reaching the ultimate strength and local buckling of the face plate was observed after reaching the ultimate strength. The effect of web plate pitting on the lateral-distortional buckling strength was found to be small but the ultimate strength decreases with increase in the degree of pitting intensity. In the 3-point bend tests, concentrated load has been applied vertically at the center of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, local face buckling occurred just after reaching the ultimate strength. The ultimate strength is found to be decreasing with increase in the degree of pitting intensity.

A series of non-linear FE analyses has been performed to simulate the deformation behavior observed in the tests. It has been revealed that even in the case of randomly distributed pitting corrosion the ultimate strength of the structural models was almost the same as that of the structural models with uniform corrosion corresponding to the average thickness loss.     

液压油缸的承载力

本文用压溃理论分析计算液压油缸的承载力,综合考虑了油缸本身初弯曲、受载偏心、活塞杆和缸筒的非刚性连接、铰支承摩擦、自重以及中间支承偏心等因素对油缸承载力的影响,并用实验对理论分析进行了验证,得到了较好的结果。     

Controlled pipeline lateral buckling by reeling induced curvature imperfections

Expansion of pipelines installed on the sea floor due to the passage of high temperature and pressure hydrocarbons leads to lateral buckling. Interaction with a frictional sea floor can result in localization of such buckles, which must be controlled to ensure that the local bending is within acceptable limits. Periodic geometric imperfections introduced to a pipeline installed by reeling using the Residual Curvature Method are modeled and their effectiveness as expansion loops is evaluated. The imperfections are generated by allowing chosen lengths of the line to retain a small curvature by judicious action at the straightener. The model properly accounts for the complex interactions between geometric and material nonlinearities with frictional forces. It is demonstrated that as the temperature increases, the line can buckle in a snap-through manner, or can grow stably usually causing plastic deformation in its crest. The behavior is governed by the length, curvature, amplitude and periodicity of the imperfection, and by the lateral and axial frictional forces that develop. The effect of each of these variables is studied parametrically. Overall, the Residual Curvature Method is found to be a viable and effective method of controlling lateral buckling. The results provide guidance on the optimal periodicity, how to avoid snap-through buckling, and how to simultaneously minimize plastic bending.     

自升式平台桩靴强度分析

合理的桩靴设计是立插桩式海洋自升式平台在海上安全工作的关键因素之一。以某自升式海洋平台桩靴为研究对象,利用规范和SACS软件对桩靴结构设计进行强度校核和屈曲强度分析,并对桩靴的承载力和计算方法进行研究。     

小径厚比深水管道的压溃屈曲研究

深水管道所处的特殊海洋环境极易导致其发生压溃屈曲破坏.通过深入分析不同径厚比深水管道的压溃屈曲特点,并对具有不同径厚比及初始椭圆度的深水管道模型进行了压溃屈曲及后屈曲行为的计算分析.研究发现,压溃屈曲的经典理论公式并不适用于小径厚比深水管道.文章基于经典理论和数值模拟结果,得到了适用于小径厚比深水管道压溃屈曲分析的临界压力修正公式,进而对小径厚比深水管道的压溃屈曲评估提供理论支撑和工程推荐.     

桁材开孔腹板的线性屈曲强度分析

船体在总纵弯曲时甲板纵桁和船底纵桁承受较大的轴向压力,而在桁材腹板上开孔会影响其腹板的屈曲强度.针对这一问题,应用有限元屈曲特征值分析方法对受轴向压力开孔腹板的屈曲载荷进行计算.通过对计算结果的分析,对开孔尺寸和开孔位置对腹板屈曲强度影响的规律进行了归纳,并对腰圆孔和圆孔对腹板屈曲的影响程度做出了比较,对船体结构中腹板开孔尺寸及位置提出了一些建议.     

双碑嘉陵江大桥非线性稳定分析

为保证双碑嘉陵江大桥结构的安全,对该桥进行非线性稳定分析。采用ANSYS建立全桥有限元模型,考虑梁柱、大位移、斜拉索垂度等几何非线性因素,采用弹塑性分析中的各向同性强化模型考虑材料非线性,材料本构关系选用双折线模型。分析结果表明:该桥的稳定性满足规范要求,考虑几何非线性的结构稳定安全系数和仅考虑线弹性的结构稳定安全系数差别不大;考虑材料非线性的结构稳定安全系数大概是仅考虑线弹性的结构稳定安全系数的0.4倍左右;考虑几何与材料双重非线性的结构稳定安全系数是仅考虑线弹性的结构稳定安全系数的0.3倍左右。建议非线性稳定的安全系数参考结构丧失承载能力的安全系数的计算方法。     

余弦载荷作用下圆锥壳的动力屈曲研究

本文采用数值方法对圆锥壳在余弦载荷作用下的动力屈曲问题进行了探讨.利用非线性几何方程建立了锥壳的基本动力屈曲方程.采用级数展开和伽辽金法等方法对方程进行了简化,使之成为常微分方程.方程的求解则采用龙格库塔法,最后给出临界冲击载荷值.     

VLOC横撑材结构的屈曲评估及设计参数影响分析

以某超大型矿砂船(Very Large Ore Carrier, VLOC)为例,基于中国船级社(CCS)《矿砂船船体结构强度直接计算指南》和《矿砂船船体结构高级屈曲评估指南》,对VLOC边舱内强框架上典型横撑材结构的柱屈曲、扭转屈曲和组合扭转/柱屈曲强度进行计算分析。针对VLOC横撑材结构的受力特点,通过几种截面形状的比较和对水平桁宽度、面板偏心等相关设计参数的影响分析,对于改善VLOC横撑材截面形状设计和材料选用给出一些指导性的建议。