基于对流效应的寒区路堤块石层临界高度研究

为了研究块石路堤降温效应与块石层高度之间的关系,基于多孔介质自然对流理论和热传导理论引入了表征寒区块石路堤自然对流降温效应的自然对流指数,利用热传导温度分布函数获得了路堤自然对流指数随块石层高度变化的近似公式。分析表明:自然对流指数最小值对应于路堤块石层的最小高度,而其最大值对应于路堤块石层的最大高度。另外介绍了一种利用自然对流指数近似公式估算路堤块石层临界高度的方法,并具体给出了算例,最后进行了数值验算。结果表明:通过自然对流指数确定的临界高度可为寒区工程的路堤设计提供参考。     

石河道大桥桩基础施工

针对卵石地层桩基础成孔问题,根据石河道大桥实际施工实践介绍了应用冲击钻孔的方法加以解决的施工方法,并着重分析了该方法的工艺流程和内容,以及施工中的注意事项.     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

桥梁施工中实用新技术的应用

根据桥梁施工的多年实践，针对钻孔灌桩钢筋笼定位筋制作、梁板底膜预制与泄水孔预留、小型混凝土垫块制备，临时支座制作，桥面混凝土标高控制与钢筋网的保护及防水层、粘结层的设置，混凝土构件的养生等几方面施工难题，列举了一些新工艺、新方法，提出几种比较实用的应用技术。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Numerical simulation of the flow about self-propelling tanker models

A time-marching CFD simulation is performed for self-propelling ships. The flow about the hull is simulated by the finite-volume method, and the propeller action is approximated as a propeller disk for which the solution is given by a simplified propeller model. The interaction of two flow models is treated in a time-marching procedure converging towards the steady self-propelling condition. This method is applied to five tanker models, and detailed comparisons are made between the simulated results and corresponding experimental results. It is shown that the flow field in the self-propelling condition is qualitatively well reproduced in the simulation, and the estimated thrust deduction factors for the five hull forms agree well with measured ones. However, the effective wake factors are underestimated, since the Reynolds number in the simulations differs from that in the experiment.     

尾管密封失效分析

本文对船舶常用尾管密封装置构造了“失效树”，应用FAT方法对影响密封失效的因素进行了定性分析，着重讨论了轴系振动的影响。     

黄铜管焊缝高温短时退火组织的研究

用光镜对单相黄铜管焊后和冷变形后的焊缝在高温短时退火后的组织进行了研究。结果表明，焊后不经过冷变形的焊缝，退火后组织为粗大的、并垂直于焊缝的条形晶粒和粗大的等轴晶粒；经过冷变形后，焊缝的不同原始组织在退火后都将发生再结晶，影响管坯表面质量的铸造组织消失，组织细化，文中对试验结果进行了分析．