小直径盾构施工中管片纵向应力监测研究

为了探索小直径盾构法隧道在施工过程中管片纵向应力的变化规律,对北京槐房再生水厂污水隧道管片纵向应力进行了现场监测:将第976环、第1 054环管片分别设为第1和第2监测断面,2监测断面各预埋5个纵向应力计,各监测断面从本监测断面管片安装后即开始监测,当盾构掘进至第1 129环时停止监测。研究表明:1)在管片离开盾尾50环后,其纵向应力波动值小于管片拼装期间应力值的5%。2)在盾构掘进期间,管片距离盾构越远,其纵向压应力值越小。3)在管片拼装期间,管片距离盾构越远,其纵向压应力经历了先增大后减小的过程。4)管片距离盾构108环后,该管片纵向压应力趋近于0.2~0.3 MPa。5)随着盾构推进,管片纵向应力经历了4个阶段的变化过程,即周期性剧烈波动阶段—动态稳定阶段—逐渐衰减阶段—趋于稳定阶段。     

薄基岩顶板隧道爆破施工围岩稳定性分析

为更有效地进行薄基岩顶板条件下隧道施工安全控制,以某高速公路隧道为工程背景,运用数值模拟的方法,分别研究不同顶板厚度下隧道爆破施工引起的围岩振速分布特征及其对围岩的损伤情况,并进行围岩稳定性分析。结果表明:1)当顶板厚度在5 m及以上时,围岩是稳定的;2)当顶板厚度为3 m时,最危险横断面上基岩顶板内开始产生严重的拉伸裂缝及一些径向裂缝,将形成超挖;3)当顶板厚度≤2 m时,径向裂缝贯穿顶板岩体,围岩稳定性较差,在掌子面后1 m内可能发生塌落、掉块等事故。     

城市地下道路分(合)流匝道通风阻力特性

为分析多点进出结构的城市地下道路空气流动特性,以长沙市营盘路湘江隧道为原型,通过现场实测、缩尺模型试验以及CFD软件数值模拟方法,对分(合)匝道通风阻力特性进行了研究,考察了雷诺数、风量比、分岔角度对分(合)流匝道阻力特性的影响规律。研究结果表明:1)主隧道与匝道风量比、主隧道与匝道夹角是影响分(合)流匝道局部阻力系数的关键因素;2)城市地下道路分(合)流匝道局部阻力变化特性,不宜简单套用通风管道的三通构件的参数;3)结合最小二乘法和Matlab软件对计算结果进行多因素回归分析,给出了基于长沙营盘路湘江隧道的分(合)流匝道主隧道和匝道的局部阻力系数关联式。研究结果可为复杂结构城市地下道路通风系统阻力特性分析及通风工程优化设计提供方法参考。     

“中—尼—印铁路通道”线路设计及建设可行性分析

随着我国"一带一路"倡议的推进,跨国运输通道的建设成为倡议实施的关键环节之一,而我国建设复杂地质条件下跨国基础设施的经验尚不丰富。"中—尼—印铁路通道"是一条途经尼泊尔,连接中国和印度2个大国的运输通道,基于实地考察,分析该通道建设的必要性及建成后的效益,对线路进行初步规划,并总结该通道建设的难点:铁路轨道坡度大;沿线区域地质构造复杂;周边基础设施落后,施工条件恶劣;大量深长隧道以及大跨径高桥梁;环境以及气候条件复杂。同时对沿线隧道以及桥梁的建设可行性进行分析,并给出施工建议:沿线隧道采用以TBM法为主、钻爆法为辅的施工方法;桥梁建设则因地制宜,根据不同区间的地质特点,采用相应的建设方法。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

拱架式预切槽施工机械在黄土隧道施工中的应用

隧道预切槽施工技术在国外应用比较广泛,但在我国应用还较少。针对黄土地质专项研制了国内首台拱架式预切槽机,并在黄土隧道进行了施工试验。通过施工试验,掌握设备定位、分区切灌、设备行走、施工作业组织等关键技术,并提出应用改进及优化措施。试验结果表明切槽系统工作状态和设备切削、喷灌功能满足设计及施工试验要求,为预切槽同步切削喷灌一体化研究提供了数据支撑和研究方向。     

Modelling,simulation and applications of longitudinal train dynamics

ABSTRACT

Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces – the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.